36" (91.4 CM) AND 48" (121.9 CM) HOOD LINER ... - Whirlpool

More documents

Recommendations

Info

Install Range Hood LinerBThe hood liner attaches to the hood support using four mountingscrews and washers.NOTE: Hood support must be capable of supporting75 lb (34 kg).1. Using 2 or more people, lift the hood liner into place.2. Install the hood liner using four 5 x 45 mm screws to the hoodsupport and tighten securely.ADECInstall Hood Liner Internal Blower MotorNOTE: Your hood liner requires you to purchase either an internaltype or an in-line (external type) blower motor system. See“Blower Motor System” in the “Accessories” section.The internal blower system can be mounted for top venting orrear venting. For top venting, the mounting bracket and springclip that come with the blower system will mount to the top panelof the hood liner. For rear venting, the mounting bracket andspring clip that come with the blower system will mount to therear panel of the hood liner.Prepare the Internal Blower SystemIMPORTANT: Perform steps 1-4 before mounting the hood liner.1. Remove grease filters from hood liner. See the “Range HoodCare” section in the Use and Care Guide.2. Install the motor support bracket using three 4.2 x 8 mmscrews. Screw bracket to the inside top or back (alternatelocation on some models), toward the left side of the hoodliner.3. Install motor spring clip using two 4.2 x 8 mm screws. Screwspring clip to the inside top or back (alternate location onsome models) of the hood liner at the proper location for theselected motor system. Slide the mounting tab of the springclip through the slot in the panel and secure with the screws.Use the inside set of mounting holes for the single motorsystem. Use the outside set of mounting holes for the dualmotor system.A. 4.2 x 8 mm screws (3) for motor support bracketB. 4.2 x 8 mm screws (2) for motor spring clipC. Motor support bracketD. Motor spring clip (single motor assembly location)E. Motor spring clip (dual motor assembly location)4. Install the 6 mm nuts to the outside top or outside back(alternate location on some models) of the hood liner at theproper location for the selected motor system.■ Two 6 mm nuts are required for the single motor system.Clip nuts into the small square notches located at the leftand right end of the square vent opening.■ Five 6 mm nuts are required for the dual motor system.Clip nuts into the small square notches, one located in thefront of the square vent opening and the other fourlocated at the left and right ends of the square ventopening.AAABA. Clip nut (6 mm) locations for dual motor assembly (quantity 5)B. Clip nut (6 mm) locations for single motor assembly (quantity 2)5. Mount hood liner. See the “Install Range Hood Liner” section.8
Install Hood Liner Internal Blower Motor1. Install the hood liner blower motor assembly inside the hoodliner canopy with the wiring connection to the left for thesingle motor system and to the front or top for the dual motorsystem.3. Run the power supply wires and connector from the rangehood through the hole in the right end of the motor mountingplate.ASingle Blower Motor AssemblyBAA. Wiring connectionA. Motor mounting plate holeB. Power supply wires and connector4. Push the right end of the motor mounting plate up and snap itinto the spring tab.NOTE: The spring tab should be outside the slot in themounting plate.Dual Blower Motor AssemblyAABA. Motor mounting plateB. Spring clipA. Wiring connection2. Slide the left mounting plate flange under the motor mountingbracket.5. Align mounting holes in motor mounting plate with motormounting clip nuts and install 6 x 16 mm screws and6.4 mm lock washers (quantity 2 for single motor; quantity 5for dual motor).CBAABA. Motor mounting bracketB. Mounting plate left flangeA. Screw with lock washerB. Mounting hole in motor mounting plateC. Clip nut (6 mm)9
Page 2 and 3: TABLE OF CONTENTSRANGE HOOD SAFETY
Page 4: INSTALLATION REQUIREMENTSTools and
Page 7: ■ It is recommended that the vent
Page 11 and 12: Complete Preparation1. Determine an
Page 13 and 14: ABCDFEComplete Installation and Che
Page 15 and 16: IMPORTANT: Clean the hood and greas
Page 17 and 18: When calling for assistance or serv
Page 19 and 20: SÉCURITÉ DE LA HOTTE DE CUISINIÈ
Page 21 and 22: EXIGENCES D'INSTALLATIONOutils et p
Page 23 and 24: La sortie à l’extérieur du circ
Page 25 and 26: Installation de la caisse de la hot
Page 27 and 28: 6. Relier le connecteur du cordon d
Page 29 and 30: AVERTISSEMENTRisque de choc électr
Page 31 and 32: La hotte de cuisinière est conçue
Page 33 and 34: Boîtier de connexionNeu L TerreJA-
Page 35 and 36: GARANTIE DES GROS APPAREILS MÉNAGE

36" (91.4 CM) AND 48" (121.9 CM) HOOD LINER ... - Whirlpool

Create successful ePaper yourself

Delete template?

Save as template?