manual verificado ar-130 con pasadores y posventa ... - Badepool.de

? Decrease in the flow rate of feedback is detected, after checking that the pump is well primed.
? Pressure gauge indicates that there is excess pressure (needle pointing between yellow and red, or on red).
5.3.1 For filter backwash, proceed as follows:
? Disconnect the filter from the power point. Never move the selector valve while the motor is running.
? Loosen the upper triangular knob on the valve by turning it until the cover is lifted from its housing and turned. Place
the valve on the backwash setting, reinserting the cover in its housing and retightening the knob by turning it. Do not
overtighten the knob as the valve may be damaged. Fig. 12.
? Connect the Ø38 mm x 1.5 m. hose to the valve waste (fig 8, pos 8) outlet and direct the other end of the hose to a
drain or sewer.
? Start up the filter for approximately 2 min (until no further impurities are released with the water).
? Stop the filter and leave it at a standstill for 2 min. to allow the silica sand to settle and prevent it from being released
into the pool.
? Reset the valve to the desired setting (filtration or closed) and remove the hose from the drain outlet.
NEVER HANDLE THE VALVE WHILE THE MOTOR IS RUNNING
5.4 Draining the pool
The following accessory is provided to empty the pool: AR2071 portable submersible pump.
The filter allows you to drain nearly the entire pool after the bathing season has ended. In order to do so, you should set
the top selector valve on the waste setting (fig. 12) without plugging in the filter and connect a hose to the free outlet of
the selector valve in order to channel the water to the drain or sewer. Then, depending on the skimmer model, proceed as
follows:
5.4.1 AR-130, AR-130L model (with wall skimmer for Dream Pools and Jet Pool swimming pools):
? Remove the inner basket from the skimmer and cover the suction inlet with the plug supplied for this purpose.
? Disconnect the suction hose from the skimmer inlet. Loosen the clamp which secures the hose and support it so that
no water leaks and the filter remains primed.
? Remove the hose, covering the end so that it remains primed and submerge it immediately in the pool.
? Weigh down the end of the suction hose with a heavy object which can not damage the liner so that it is forced to sink
to the bottom of the pool.
? Start up the pump and drain the pool. Remember that the filter will not fully drain the pool. When a few cm. of water
are left and the pump no longer sucks in water, shut if off.
? If you are going to refill the pool with water, first manually remove the remaining water without damaging the liner.
? If you are going to disassemble the pool, you can fold the bag with the remaining water in the centre and, after
removing the plate, unfold the bag in order to drain it fully. This operation should not be performed except to
disassemble the pool.
5.4.2 AR-130E, model (with self-supporting skimmer for Magic Pools):
To empty the pool, you can use the pool drain or the cleansing unit:
? Raise the self-supporting skimmer until it is hanging outside the pool, to prevent water from entering the skimmer.
? Disconnect the suction hose from the skimmer inlet by the outer part of the pool wall. Loosen the clamp which secures
the hose carefully so that the liner is not damaged. Hold the hose so that it does not leak and remains primed.
? Remove the hose, covering the end so that it remains primed and submerge it immediately in the pool.
? Weigh down the end of the suction hose from the skimmer inlet with a heavy object which can not damage the liner so
that it is forced to sink to the bottom of the pool.
? Start up the pump and drain the pool. Remember that the filter will not fully drain the pool. When the pump no longer
sucks in water, shut if off.
? If you are going to refill the pool with water, first remove the remaining water through the drain without damaging the
pool.
The following accessory is provided to empty the pool: AR2071 portable submersible pump.
The filter allows you to drain nearly the entire pool after the bathing season has ended. In order to do so, you should set
the top selector valve on the waste setting (fig. 12) without plugging in the filter and connect a hose to the free outlet of
the selector valve in order to channel the water to the drain or sewer. Then, depending on the skimmer model, proceed as
follows:
THE HOSE SHOULD NOT CONTINUE TO APPLY SUCTION TO THE BOTTOM OF THE POOL LINER. THE PUMP
MAY BE SERIOUSLY DAMAGED IF IT OPERATES WITHOUT WATER CIRCULATION OR WITH SUCTION OF THE
LINER.
5