manual verificado ar-130 con pasadores y posventa ... - Badepool.de

5.5 Cleaning the bottom of the pool
In order to clean the bottom of the pool, use the pump filter with one of the following accessories:
“Riñón” bottom cleaner/ AR-206, “Oval” bottom cleaner / AR-207 (you will also need a Ø38 mm hose / AR-210 and the
pole / AR-102). To purchase these items, consult your establishment or ask the After-Sales Service provided by the pool
manufacturer. Always use original replacement parts.
A hose which extends beyond the length required to reach all points of the pool is more difficult to use. Cut off the section
of the hose which is not needed. Check that the rubber terminals conserve their seal.
5.5.1 Priming the bottom cleaner hose:
Insert the bottom cleaner into the pool vertically, with the pole and the hose connected. Let it fill with water and keep the
rest of the hose outside of the water. Continue to insert the hose in the water slowly by 50 cm sections which should be
submerged at the same time as they are completely filled with water. Proceed up until the end, when the entire hose is
filled with water and submerged. If the hose is not fully primed, the bottom cleaner will not perform suction and the
cleansing unit may be damaged if it is forced to operate when it is empty.
5.5.2 AR-130, AR-130L model (with wall skimmer for Dream Pools and Jet Pool swimming pools):
Place the suction cover accessory inside the skimmer with the inlet facing upwards. Do not remove the basket. Prime the
hose.
Starting INSIDE OF THE POOL, place the end of the hose through the skimmer hatch. Make sure that no air enters.
Connect it to the suction cover inlet and secure it at an angle to facilitate the connection. Then set it into place in a
horizontal position and continue to insert the hose. Be careful not to damage the skimmer hatch during this operation. The
skimmer water level must be at the maximum level. It should be located above the connection between the cover and the
hose to prevent air from entering.
Start up the pump on the filtration setting and proceed to clean the bottom of the pool.
5.5.3 AR-130E, model (with self-supporting skimmer for Magic Pools):
Remove the upper floating ring of the skimmer. Then, without removing the preliminary filtration basket, place the suction
cover accessory on the upper part of the skimmer with the inlet facing upwards and submerge the skimmer inside the
pool to a point which ensures that the suction cover does not draw in air.
Prime the hose.
Make sure that no air enters the hose and connect it to the suction cover inlet. The connection of the hose and the cover
should always remain submerged in order to prevent air from entering.
Start up the pump and proceed to clean the bottom of the pool.
5.6 Closed setting
The closed setting for the selector valve (fig. 12) is used to prevent water from circulating through the hoses and the filter.
6 MAINTENANCE
After the bathing season has ended, the filter should be kept in a dry place where it is protected from inclement weather.
For this purpose, after performing a final backwash to clean the silica sand, dismount the hoses and drain the water in the
filter through the tank drain plug until it is completely empty.
After removing all of the water from the filter, carefully clean the remains of silica sand from the thread before
replacing the plug. Failure to do so could damage the thread.
The filter tank drain plug should only be used in this operation.
VERY IMPORTANT: Following an extended period of inactivity, before starting up the filter check that the drive
shaft is not jammed. Remove the protection cover of the pump with a star screwdriver. Once the pump cover is
released, if it doesn’t turn, clean the wheel of the turbine as shown in section 6.1.
After stoppage for an extended period, it is also recommendable to make sure that the filter is primed before
starting up.
6.1 Care of the pump
The filter pump is designed to operate without any specific maintenance. Nevertheless, if the unit is used in pools which
are extremely dirty, especially with leaves, this may cause the pump shaft to jam. In this case, proceed as follows:
? Disconnect the unit from the power point.
? Place the valve on the closed setting.
? Insert the sealing plug on the skimmer.
? Disconnect the 0.4 m. hose, and then loosen the 2 (two) screws that fasten the cover of the pump body.
? Clean the wheel. If you see that it is broken, ask the pool manufacturer about replacement.
? Reinsert the pump cover. Ensure that the coupling is fully centred and firmly tightened.
? Connect the sleeve to the pump cover.
? Remove the sealing plug from the skimmer.
6.2 Solving breakdowns and technical service
This filter includes instructions which are especially designed for family use. There is no need for professional assistance,
except for in special cases. The following are some of the problems and causes which may arise over time after years of
6