manual verificado ar-130 con pasadores y posventa ... - Badepool.de
manual verificado ar-130 con pasadores y posventa ... - Badepool.de
manual verificado ar-130 con pasadores y posventa ... - Badepool.de
Create successful ePaper yourself
Turn your PDF publications into a flip-book with our unique Google optimized e-Paper software.
service by the filter. Normally you can solve these problems on your own. If not, <strong>con</strong>tact the pool manufacturer at the<br />
telephone and time indicated in the instructions.<br />
PROBLEM CAUSE SOLUTION<br />
The filter leaks through the hose terminals<br />
After the filter has st<strong>ar</strong>ted up, there is no flow in<br />
the feedback nozzle.<br />
Improper <strong>con</strong>nection between the terminals and<br />
the hoses.<br />
The valve is not on the filtration setting.<br />
The filter is above the level of the unprimed<br />
water.<br />
7<br />
Place Teflon in the housings. Insert the hose<br />
terminals up until the bottom of the housing and<br />
tighten the clamps.<br />
Dis<strong>con</strong>nect the filter and place the valve on the<br />
correct setting.<br />
Place the filter in the correct position and prime<br />
it.<br />
The pump is jammed and must be disassembled. See the section 6.1<br />
The suction cover or the skimmer plug have<br />
been inserted.<br />
Remove the suction cover or the skimmer plug.<br />
Intermittent operation<br />
Low water level on skimmer<br />
The filter is not primed.<br />
Fill the pool and prime the filter.<br />
Prime the filter.<br />
The flow rate of the filter is low.<br />
Due to use, the filter is dirty.<br />
The filter is not primed.<br />
Perform a backwash.<br />
Prime the filter.<br />
The <strong>con</strong>nection between the valve and the filter Clean the sand from the opening. Insert the<br />
Water comes out through the filter opening. is dirty.<br />
coupling on the valve properly and tighten the<br />
Metal band is loose.<br />
metal band firmly.<br />
The filter valve leaks through the drain terminal.<br />
Inner coupling damaged due to improper use of<br />
chemical product.<br />
Change the top valve cover.<br />
Do not put chemical products in the prelimin<strong>ar</strong>y<br />
filtration skimmer basket.<br />
Valve head broken due to improper use.<br />
(overtightening)<br />
Change the valve head. Do not overtighten.<br />
The motor will not st<strong>ar</strong>t up. There is no noise or<br />
vibration.<br />
No current in the electric line.<br />
Loose motor terminals.<br />
Check that there is current in the electric line.<br />
Switch on the motor (section 6) and check the<br />
motor terminals.<br />
The motor does not st<strong>ar</strong>t up but a buzzing sound<br />
can be he<strong>ar</strong>d.<br />
Drive shaft jams after prolonged inactivity.<br />
Con<strong>de</strong>nser damaged ( 6?F )<br />
See section 6<br />
This can be purchased in an electricity shop<br />
(replacement un<strong>de</strong>r product w<strong>ar</strong>ranty).<br />
Check the hose clamps.<br />
Water leaks through the protective housing.<br />
Remove the housing as shown in section 6, and<br />
analyse the reason for water loss.<br />
If the leak is between the pump and the motor,<br />
<strong>con</strong>tact the After-Sales Service provi<strong>de</strong>d by the<br />
pool manufacturer.<br />
7 ASSEMBLY OF THE PRESSURE GAUGE.<br />
1 2 3 NO PRESSURE GAUGE
Change language