FCD-2400I

More documents

Recommendations

Info

3. Battery 4. Speed switch 5. Torque adjusting ring 6. Percussion function adjusting ring 7. Drill chuck 8. Side handle 2. SAFETYREGULATIONS The following pictograms appear in these operating instructions: Carefully read the instructions. According to the necessary, applicable safety standards and guidelines under ideal conditions. Class II charging station – doubly insulated – no grounded plug is required. Refers to risk of injury, life-threatening danger and possible damage to the device if the operating instructions are not heeded. Indicates the presence of an electrical voltage. Do not dispose of in household waste. Ni-Cad batteries can be recycled. Drop them off at a disposal center for chemical wastes, so that they can be recycled or disposed of in an eco-friendly manner. Only for use indoors Never throw the batteries into an open fire In the event of a disruption, the transformer is not dangerous Adjustable speed regulator Wear hearing protection 04 Ferm Ferm 93 GB D NL F E P I S FIN N DK
GB D NL F E P I S FIN N DK 92 Ferm Damaged and/or disposed of electrical or electronic devices must be dropped off at the recycling stations intended for that purpose. Important safety instructions for the charger and battery block Should you come into contact with acid from the battery, immediately wash the acid off with water. If acid gets into your eyes, immediately rinse your eyes with water and see a doctor at once! The maximum charging time of the battery is approx. 100 minutes. Important! When using battery-operated tools, basic safety precautions should be taken, including those listed below, in order to reduce the risk of a fire, depleted batteries and personal injury. 1. Read and heed the operating instructions and safety information for the charger and battery block before use! 2. Important! Only use the charger and battery that were supplied by the manufacturer, otherwise an accident may occur. 3. Protect the charger, battery block and power tool from moisture, e.g. from rain or snow. 4. Before using the charger, always check to ensure that all the cables are connected correctly. 5. If you discover damage to the power cables, you must discontinue using the charger. Have the power cable replaced at once. 6. If you are not using the charger, the power plug must be disconnected from the outlet. Do not pull the power plug by the power cable. 7. If the charger falls, or is subjected to some other serious physical shock, have it examined for damage before the next use by a qualified specialist work shop. Damaged components must be repaired. 8. Handle the battery block with care, never allow it to fall and do not strike it in any way. 9. Never try to repair the charger or battery block by yourself. Repairs must always be carried out by a qualified specialist work shop, otherwise an accident may occur. 10. Before cleaning or servicing the charger or battery block, always pull the device’s power plug out of the socket. 11. Never charge the battery block when the ambient temperature is under 10 °C or over 40 °C. 12. The air openings on the charger must always be free of obstruction. 13. The battery block must not be allowed to short-circuit. During a short-circuit, the current flows at very high intensity. Over-heating, risk of fire or an exploded battery block may result. This can lead to damage to the battery block or an increased risk of an accident for the user. Therefore: • Do not connect any cables to the poles of the battery block. • Ensure that no metallic objects (nails, staples, coins, etc.) are in the battery block receptacle. • Do not expose the battery block to water or rain. • Only use the supplied battery block in combination with this battery-operated drill/power screwdriver in order to prevent failures and/or hazards. • Abattery block that is damaged or no longer chargeable must be disposed of as special waste. Do not throw it away in ordinary household waste. • Never throw the battery block into fire or water. It may explode! Ferm 05 GB D NL F E P I S FIN N DK
Page 1 and 2: GB Subject to change D Änderungen
Page 3: Spare parts list Ferm No. Descripti
Page 7 and 8: GB D NL F E P I S FIN N DK CE KONFO
Page 9 and 10: GB D NL F E P I S FIN N DK Sørg fo
Page 11 and 12: GB D NL F E P I S FIN N DK Elektris
Page 13 and 14: GB D NL F E P I S FIN N DK 2. Tænd
Page 17 and 18: GB D NL F E P I S FIN N DK Boring B
Page 21 and 22: GB D NL F E P I S FIN N DK 3. Batte
Page 23 and 24: GB D NL F E P I S FIN N DK CE YHDEN
Page 25 and 26: GB D NL F E P I S FIN N DK Poraamin
Page 27 and 28: GB D NL F E P I S FIN N DK Sähköt
Page 29 and 30: GB D NL F E P I S FIN N DK 3. Akku
Page 33 and 34: GB D NL F E P I S FIN N DK Se till
Page 37 and 38: GB D NL F E P I S FIN N DK 3. Batte
Page 39 and 40: GB D NL F E P I S FIN N DK CE DICHI
Page 41 and 42: GB D NL F E P I S FIN N DK • Impo
Page 43 and 44: UK D NL F E P I S SF N DK • Contr
Page 45 and 46: UK D NL F E P I S SF N DK Informazi
Page 47 and 48: UK D NL F E P I S SF N DK CE DECLAR

FCD-2400I

Create successful ePaper yourself

Delete template?

Save as template?