FCD-2400I

More documents

Recommendations

Info

GB D NL F E P I S FIN N DK Electrical safety Always check to see whether the voltage of your battery corresponds to that given on the rating plate. Also check to see whether the voltage of your power supply corresponds to the input voltage of the battery charger. The battery charger is doubly insulated; therefore, it does not need to be grounded. If it becomes necessary to replace the power cable, this must be carried out by the manufacturer or an authorized representative in order to prevent safety risks. 3. INSTALLING THE ACCESSORIES Always remove the battery before beginning an installation. Installing and removing drill bits Fig. B In addition to drilling, the device can also function as a screwdriver and accommodate bits with hexagonal shafts. • Loosen the drill chuck (7) by turning it by the flanging (B). • Insert the shaft of the drill bit into the receptacle of the drill chuck. • Tighten the drill chuck until the shaft of the drill bit is firmly in place. • Loosen the drill chuck if you want to change the drill bit. • Before connecting the charger, check to ensure that the outer surface of the battery block or tool is clean and dry. Before connecting the charger, check to ensure that the outer surface of the battery block or tool is clean and dry. Installing and removing the battery Fig. C • Ensure that the direction of rotation switch (1, Fig. A) is in the center position in order to prevent the device from being unintentionally switched on. • Insert the battery (3) into the base of the device as shown in the drawing. Press in firmly on the battery until it locks into place. • Before removing the battery, press the latching buttons (A) on both sides. Then pull the battery out of the base of the device. Side handle Use the additional handle supplied with the device. Failure to maintain control of the device can lead to injuries. 06 Ferm Ferm 91 GB D NL F E P I S FIN N DK
GB D NL F E P I S FIN N DK CE KONFORMITETSERKLÆRING (DK) Vi erklærer under almindeligt ansvar, at dette produkt er i overensstemmelse med følgende standarder eller normative dokumenter: EN60745-1, EN60745-2-2, EN55014-1, EN55014-2, EN60335-1, EN60335-2-29, EN61000-3-2, EN61000-3-3. fra 01-04-2006 ZWOLLE NL W. Kamphof Quality department iht. bestemmelserne i direktiverne: 98/37/EWG, 73/23/EWG, 89/336/EWG Vores firmapolitik bygger på løbende forbedring af vores produkter, og vi forbeholder os retten til at ændre produktspecifikationer uden varsel. Ferm BV • Lingenstraat 6 • 8028 PM Zwolle • Holland 90 Ferm • Slide the side handle over the drill chuck. • Turn the side handle to the desired position. • Tighten the side handle by rotating it clockwise. 4. OPERATING Always observe the safety information and comply with the relevant regulations. Wear hearing protection when using this device. Excessive noise can cause hearing loss. When drilling, do not hold any workpieces using your hands. Always use a vice or some other clamping device. Hold the device firmly and press the drill evenly into the workpiece. Do not overload the device. Only use drill bits that show no signs of wear. Worn drill bits have a negative effect on the functional capabilities of the device. Setting the speed Fig. A The device has two drilling speeds. • Set the speed selector switch (4) to ´1´ for slow drilling or for slow loosening and/or tightening of screws. • Set the speed selector switch to ´2´ for fast drilling. Never change the switch while the motor is running!!! Setting the torque Fig. A The device has 16 different torque settings that can be used to determine the amount of force to be used for tightening or loosening screws. • Set the torque adjusting ring (5) to the desired position. The torque settings that are available for selection are specified on the adjusting ring by the numbers 1 to 15 with a decimal point between two numbers to designate an intermediate position (a total of 16). • It is best to select the lowest position needed in order to turn the screw. Select a higher position if the torque slips. Tightening and loosening screws Fig. E • Set the direction of rotation switch (1) to position ´R´ for tightening screws. • Set the direction of rotation switch to position ´L´ for loosening screws. Ferm 07 GB D NL F E P I S FIN N DK
Page 1 and 2: GB Subject to change D Änderungen
Page 3 and 4: Spare parts list Ferm No. Descripti
Page 5: GB D NL F E P I S FIN N DK 92 Ferm
Page 9 and 10: GB D NL F E P I S FIN N DK Sørg fo
Page 11 and 12: GB D NL F E P I S FIN N DK Elektris
Page 13 and 14: GB D NL F E P I S FIN N DK 2. Tænd
Page 15 and 16: GB D NL F E P I S FIN N DK CE KONFO
Page 17 and 18: GB D NL F E P I S FIN N DK Boring B
Page 21 and 22: GB D NL F E P I S FIN N DK 3. Batte
Page 23 and 24: GB D NL F E P I S FIN N DK CE YHDEN
Page 25 and 26: GB D NL F E P I S FIN N DK Poraamin
Page 27 and 28: GB D NL F E P I S FIN N DK Sähköt
Page 29 and 30: GB D NL F E P I S FIN N DK 3. Akku
Page 31 and 32: GB D NL F E P I S FIN N DK CE KONFO
Page 33 and 34: GB D NL F E P I S FIN N DK Se till
Page 37 and 38: GB D NL F E P I S FIN N DK 3. Batte
Page 39 and 40: GB D NL F E P I S FIN N DK CE DICHI
Page 41 and 42: GB D NL F E P I S FIN N DK • Impo
Page 43 and 44: UK D NL F E P I S SF N DK • Contr
Page 45 and 46: UK D NL F E P I S SF N DK Informazi
Page 47 and 48: UK D NL F E P I S SF N DK CE DECLAR

FCD-2400I

You also want an ePaper? Increase the reach of your titles

Delete template?

Save as template?