FCD-2400I
FCD-2400I
FCD-2400I
You also want an ePaper? Increase the reach of your titles
YUMPU automatically turns print PDFs into web optimized ePapers that Google loves.
GB<br />
D<br />
NL<br />
F<br />
E<br />
P<br />
I<br />
S<br />
FIN<br />
N<br />
DK<br />
Drilling<br />
Fig. D<br />
• Turn the torque adjusting ring (5) to the drilling position.<br />
Ensure that the direction of rotation switch (1) is always set to 'R' when drilling. “R”to<br />
the right. “L”- to the left.<br />
Percussion drilling<br />
Fig. D<br />
Insert an undamaged drill bit into the clamping chuck. For drilling in soft materials, such as<br />
plastic or wood, use a metal drill bit and turn the changeover switch (6) to the right until the<br />
indicating mark points to 'Drill bit' (drilling). For percussion drilling in hard materials, such as<br />
stone and concrete, turn the changeover switch to the left until the indicator mark points to<br />
'Hammer' (percussion drilling).<br />
Regularly check the clamping chuck for damage. If necessary, use coolant when<br />
drilling. When drilling in walls, bear in mind that electrical lines and water pipes may<br />
be located inside the walls.<br />
Switching ON and OFF<br />
Fig. A<br />
• Press the ON/OFF switch (2). You can regulate the speed of the device by means of power<br />
transmission to the switch.<br />
• When you release the ON/OFF switch (2), the drill chuck stops immediately and does not<br />
continue to run.<br />
• Turn the direction of rotation switch (1) to the center in order to disable the device in the<br />
switched off state. Do not lay the device down until the motor comes to a complete stop. Do<br />
not lay the machine down in dusty areas. Dust or grime can enter through the air ventilation<br />
openings.<br />
Charging the battery<br />
Fig. E<br />
The battery charger is only suitable for charging type <strong>FCD</strong>B-2400 batteries.<br />
• Insert the battery (Fig. A-3) into the battery charger (9) as shown in the drawing. When<br />
doing so, note the + and - polarisation markings.<br />
• Plug the battery charger's power plug into the power supply outlet. The quick charge lamp<br />
(10) illuminates.<br />
• Once the green lamp (11) illuminates indicating conservation charge, charging has<br />
completed.<br />
The battery is ready for use<br />
Only use the battery charger in a dry environment with a temperature of between 10 °C and 40<br />
°C. The battery for your power drill is not charged at the factory. Before the first use, 1 to 2 hours<br />
are required in order to reach a full charge. The ultimate capacity of the battery is reached after<br />
4 to 5 charging/discharging cycles.<br />
08 Ferm<br />
Fjern fastsiddende snavs med en blød klud fugtet med søbevand. Brug ikke opløsningsmidler,<br />
som f.eks. benzin, alkohol, ammoniak, osv. Disse midler kan beskadige plastikdelene.<br />
Smøring<br />
Maskinen behøver ingen smøring.<br />
Fejl<br />
Skulle der f.eks. opstå problemer efter brug af en del, skal du sætte dig i forbindelse med den<br />
adresse, der er angivet på garantikortet. I bagerste del af denne brugsanvisning findes en<br />
udførlig oversigt over de dele, der kan bestilles.<br />
Miljø<br />
For at forhindre transportskader, leveres maskinen i en solid emballage. Emballagen består<br />
hovedsageligt af genbrugsmateriale. Udnyt også muligheden for at genbruge emballagen.<br />
Defekte og/eller bortskaffede elektriske eller elektroniske apparater skal afleveres<br />
på de relevante genbrugsstationer.<br />
Garanti<br />
Læs garantibetingelserne på det vedlagte garantikort. Slid af skruebits dækkes ikke af<br />
garantien.<br />
Ferm 89<br />
GB<br />
D<br />
NL<br />
F<br />
E<br />
P<br />
I<br />
S<br />
FIN<br />
N<br />
DK