Create successful ePaper yourself
Turn your PDF publications into a flip-book with our unique Google optimized e-Paper software.
ENGLISH<br />
10.2 LED RT<br />
The red LED indicates the operating conditions of the control:<br />
In set-up mode<br />
• Limit switch actuated = LED is off<br />
• Limit switch not actuated = LED is on<br />
Display when teaching in the radio<br />
• Flashes 1x for channel 1 (impulse command)<br />
• Flashes 2x for channel 2 (partial opening command)<br />
• Flashes quickly when saving the radio code<br />
Display when deleting the radio<br />
• Flashes slowly to signal readiness for deletion<br />
• Flashes quickly while deleting all radio codes<br />
Display of the button inputs, radio<br />
• Actuated = LED is on<br />
• Not actuated = LED is off<br />
In normal mode<br />
Flashing code as an error/diagnosis display<br />
10.3 Display of errors/warnings<br />
The red LED RT helps to easily identify causes when<br />
operation does not go according to plan.<br />
NOTE:<br />
If normal operation of the sliding gate operator with the radio<br />
receiver or circuit board button T is otherwise possible, a<br />
short circuit in the external button's connecting lead or in the<br />
button itself can be recognised through the behaviour<br />
described here.<br />
Display flashes 2x<br />
Error/warning<br />
Safety/protective device has responded<br />
Possible cause<br />
• Safety/protective device has been actuated<br />
• Safety/protective device defective<br />
Remedy<br />
Check safety/protective device<br />
Display flashes 3x<br />
Error/warning<br />
Force limit in CLOSE direction<br />
Possible cause<br />
Obstruction in gate area<br />
Remedy<br />
Remove obstruction; check forces, increase if necessary<br />
Display flashes 4x<br />
Error/warning<br />
Hold or static current circuit is open, operator at a standstill<br />
Possible cause<br />
• Normally closed contact at terminal 12/13 is open<br />
• Electric circuit interrupted<br />
Remedy<br />
• Close contact<br />
• Check electric circuit<br />
Display flashes 5x<br />
Error/warning<br />
Force limit in OPEN direction<br />
Possible cause<br />
Obstruction in gate area<br />
Remedy<br />
Remove obstruction; check forces, increase if necessary<br />
Display flashes 6x<br />
Error/warning<br />
System error<br />
Possible cause<br />
Internal error<br />
Remedy<br />
Perform a factory reset (see section 11) and teach in the<br />
control again (see section 4.2) or exchange it if necessary<br />
Display flashes 7x<br />
Error/warning<br />
Peak force<br />
Possible cause<br />
• Motor blocked<br />
• Force cut-out has not responded<br />
Remedy<br />
Check the motor for seizure<br />
10.4 Error acknowledgement<br />
If an error occurs, this can be acknowledged, provided the<br />
error is no longer present.<br />
▶ On pressing the internal or external impulse generator,<br />
the error is deleted and the gate travels in the<br />
corresponding direction.<br />
11 Resetting the Control/Restoring<br />
Factory Settings<br />
To reset the control (taught-in end-of-travel positions,<br />
forces):<br />
1. Set DIL switch 2 to ON.<br />
2. Immediately press circuit board button P briefly.<br />
3. When the red LED flashes rapidly, DIL switch 2 must be<br />
quickly set to OFF.<br />
The control has now been reset to the factory settings.<br />
12<br />
Dismantling and Disposal<br />
Note:<br />
When disassembling, observe the applicable regulations<br />
regarding occupational safety.<br />
Have a specialist dismantle the sliding gate operator in the<br />
reverse order of these instructions and dispose of it properly.<br />
16 TR10L019-A RE / 05.2010
Change language