mitac w130.pdf - tim.id.au

More documents

Recommendations

Info

8-6 Docking Main Board-B J2 J2: Docking connector. 60
9 Maintenance Diagnostics & Trouble Shooting 9-1 Introduction Each <strong>tim</strong>e the computer is turned on, the system bios runs a series of internal checks on the hardware. This power on self test(POST)allows the computer to detect problems as early as the power on stage. Error messages of post can alert you to the problem of your computer. If an error is detected during these tests, you will see an error message displayed on the screen. If the error occurs before the display is initialized, then the screen cannot display the error message. Error codes or system beeps are used to <strong>id</strong>entify a post error that occurs when the screen is not available. The value for the diagnostic port (378H) is written at the beginning of the test. Therefore, if the test failed, the user can determine where the problem occurred by reading the last value written to port 378H by the docking station or port Replicator PIO port. 9.2 Error Codes Following is a list of error codes in sequent display on the 378H port debug board. 61
Page 2 and 3:
1 General system Description ......
Page 4 and 5:
9-9 Hard Drive Test Error .........
Page 6 and 7:
A full set of software drivers and
Page 8 and 9:
MS-Sound compatible Built-in one sp
Page 10 and 11: Support I2C Index read/write and bl
Page 12 and 13: images and native display timings o
Page 14 and 15: Destination Alpha Vertex Cahec Ma
Page 16 and 17: WfM 2.0 and IEEE 802.3 compliant L
Page 18 and 19: conditions from ramp-up through ful
Page 20 and 21: Supports double sampling rate (96KH
Page 22 and 23: 2.3 Cover Switch System automatical
Page 24 and 25: One USB 2.0 Port Supports UHCI Desi
Page 26 and 27: 3.1 LCD PANEL 3 Peripheral Support
Page 28 and 29: 4 Power Management The Tetra system
Page 30 and 31: 5 Connector and Switch Definition T
Page 32 and 33: CAD19 56 CardBus address/data bus C
Page 34 and 35: Table 5-7 MDC TRANSFER BD Connector
Page 36 and 37: FPC_PWR# 62 Floppy POWER FDD_CTL# 6
Page 38 and 39: 6-1 Front View Wireless Antenna 6-2
Page 40 and 41: 6-5 Rear View USB Port 6-6 Top-open
Page 42 and 43: 6-9 Docking Module Right-Side View
Page 44 and 45: 7-2 Bottom Housing Disassembly Step
Page 46 and 47: 7-4 Memory Disassembly Step: 1. Rem
Page 48 and 49: 7-6 Keyboard Disassembly Step: 1. R
Page 50 and 51: 7-7 LCD Panel Disassembly Step: 1.
Page 52 and 53: Reassemble Step: Step 2 Step 3 1. C
Page 54 and 55: 7-10 Docking Mother Board Disassemb
Page 56 and 57: J13 J14 8 Location of Connectors /
Page 58 and 59: 8-3 D/D Board-A J500 JS500: Power
Page 63 and 64: 9-3 No Power When the power button
Page 65 and 66: 9-5 No display There is no display
Page 67 and 68: 9-7 External Monitor No Display or
Page 69 and 70: 9-9 Keyboard and Touch -pad Test Er
Page 71 and 72: 9-11 Hard Drive Test Error Either a
Page 73 and 74: 9-13 System Audio Failure No sound
Page 75: 10 System Exploded views & Circuit
show all

mitac w130.pdf - tim.id.au

Create successful ePaper yourself

Delete template?

Save as template?