Download Manual - Janome

More documents

Recommendations

Info

z x c v e q w r 12 • Inserting the bobbin q End of thread w Notch e Notch r Threading diagram z Place a bobbin in the bobbin holder with the thread running off counterclockwise. x Guide the thread into the first notch w on the front side of the bobbin holder. Draw the thread to the left, sliding it between the tension spring blades. c Continue to draw the thread lightly until the thread slips into the second notch e. Pull out about 6˝ (15 cm) of thread. v Attach the hook cover plate. Check the threading by referring to the diagram r shown on the hook cover plate.
v c z x z x c v w z q x c v w e q w r t 13 Threading the Machine • Threading the machine q Up/down needle position button w Spool * Raise the thread take-up lever to its highest position. * Raise the presser foot lifter. * Place a spool on the spool pin, with the thread coming off as shown. z Draw the end of the thread around the upper thread guide. x While holding the thread near the spool w, draw the end of the thread down around the check spring holder. c Firmly draw the thread up from right to left over the take-up lever, and down into the take-up lever eye. v Pass the thread through the lower thread guide. Slide the thread behind the needle bar thread guide on the left. Thread the needle from front to back, or use a needle threader. Needle Threader CAUTION: Turn off the power switch when using the needle threader. q Knob w Hook e Guide (a) r Guide (b) t Holder plate z Lower the presser foot. Raise the needle to its highest position. Pull down the needle threader knob q as far as it will go. The hook comes out through the needle eye from behind. x Draw the thread from guide (a) e to guide (b) r and under the hook w. Draw the thread up along the right side of the guide (b) r and slip the thread in between the guide (b) and the holder plate t. c Raise the knob in the direction of the arrow on the illustration, drawing the thread loop through the needle. v Pull the thread through the needle eye. NOTE: The needle threader can be used with a #11 to #16 needle or a blue tipped needle. Thread size 50 to 90 should also work well.
Page 1 and 2: INSTRUCTION BOOK
Page 3 and 4: SECTION I. NAME OF PARTS Names of P
Page 5 and 6: q w e r t y u i o !0 !1 !2 !3 !4 3
Page 7 and 8: q w e y r q w e t u i 5 Controlling
Page 9 and 10: w e q w r q e q e w 7 Presser Foot
Page 11 and 12: z x q c w e 9 Changing Needle CAUTI
Page 13: x x z n m v b c 11 • Winding the
Page 17 and 18: q w r e t q w q w q w 15 • Tensio
Page 19 and 20: q w q q e e w e w 17 Using the Seam
Page 21 and 22: q w e q w e r q w e 19 Pintucking q
Page 23 and 24: z x z x c q w e q w e r t y q w e o
Page 25 and 26: z x c v b n m q w e r 23 Button Sew
Page 27 and 28: c z x c t a s d f y ○ ○ ○ !0
Page 29 and 30: q w e a s d q w e a s d q w e a s d
Page 31 and 32: z z q q w e w e r q w t i w t e q r
Page 33 and 34: z q w e (1) q w r e (2) q x c (1) (
Page 35 and 36: q w e r q e q w e Patchwork q w w w
Page 37 and 38: q w e Decorative Stitch Pattern wit
Page 39 and 40: z x c v b c u q w y y r t r e z r x
Page 41 and 42: Problems and Warning Signals If a b
Page 43: 807-800-047 Printed in Taiwan

Download Manual - Janome

You also want an ePaper? Increase the reach of your titles

Delete template?

Save as template?