SAP Printing Customer documentation Volume 2 : [ZA0x] The ... - ELP

SAP Printing: Customer documentation: Volume 2: [ZA0x] page 5 / 59
1. The Device type
The device type family described here is named ZA0x.
This documentation is valid for version v016.
There are 2 families: ZA00 and ZA01, with their legacy versions ZA04 and ZA05, respectively.
It consists of the following files:
Device type file Character set
• ZA0x1vvv.PRI 1116 (Latin-1 / 0N)
• ZA0x2vvv.PRI 1416 (Latin-2 / 2N)
• ZA0xUvvv.PRI 4210 (Unicode / 18N)
The "vvv" in the name indicates the version number.
The device models supported by the device type, its features, and its limitations are indicated below.
A detailed specification is given in the next chapter.
Note: (Difference between ZA00 and ZA01)
The difference between them lies only in the support for barcoding.
Depending on the barcode solution, a different Device type has to be used.
For the "Barcode & OCR Package" (BOP), the Device type ZA001vvv has to be used.
For the "Barcode & OCR Package - Intelligent version" (BOCR), the Device types ZA01cvvv (c=1,2,U) have to be used.
For non-barcode printing, the Device types ZA00cvvv (c=1,2,U) should be used.
Note: (Legacy versions ZA04 and ZA05)
From DTX v014+, ZA00 and ZA01 support arbitrary scaling of fonts.
For compatibility with the formerly discrete font sizes, which is needed for SAP R/3 releases 3.x, you may now use the legacy versions ZA04
and ZA05, respectively. Please contact Technical support for how to obtain these.
Deviations from HPLJ4
• It has been made more modular, and easier to configure for the customer.
• The places in the "Printer initialization" actions where to configure special device features listed below have been clearly marked.
• Some Print controls have been added to support our devices' input and output bins.
• A workaround for A5 printing has been implemented.
• Print controls have been added for specifying Paper type, Color mode, and Color selection.
1.1 Devices supported
For the devices supported by these device types, refer to the corresponding section in Volume 1.
1.2 Features supported
The following device features are implemented in a generic fashion.
The tags identify the places in the "Printer initialization" action where the settings can be configured.
Please note that some settings require consistent changes at more than 1 place.
The items marked in bold face are the most important ones.
The list is ordered by importance and logic.
For the order of settings as the commands are sent to the printer, see the section "The generic command sequence" below.
Tag Feature Affected output
[PCL.01]*P INPUT BIN Input Bin Page
[PJL.04] PAPER TYPE 1/2 Paper Type / Fuser Control Page
[PCL.12] PAPER TYPE 2/2 dto Page
[PJL.17] DUPLEX MODE 1/2 Duplex Mode Page
[PCL.03]*P DUPLEX MODE 2/2 dto. Page
[PJL.16] OUTPUT BIN 1/2 Output Bin Page
[PCL.02]*P OUTPUT BIN 2/2 dto Page
[PJL.13] JOB OFFSET Job Offset Job
[PJL.02]*P STAPLING MODE Stapling Mode Job
[PJL.03]*P PUNCHING MODE Punching Mode Job
[PJL.01] RESOLUTION 1/2 Resolution Job
[PCL.14] RESOLUTION 2/2 dto Job
[PJL.15] COPIES 1/2 Number of Copies & Collation mode Job
[PCL.13] COPIES 2/2 dto Job
[PJL.14]*P ECONOMODE Econo Mode / Toner Saving Job