Views
5 years ago

SAFT ELECTRIC STORAGE BATTERY Gulfstream Aerospace P/N ...

SAFT ELECTRIC STORAGE BATTERY Gulfstream Aerospace P/N ...

Cell

Cell SAFT AMERICA INC. Component Maintenance Manual 1159SCAV519-1 Very thin, plastic bonded cadmium oxide negative plates, and nickel-hydrate impregnated positive plates. Composite separator made of synthetic fiber. Ternary electrolyte (chemically pure potassium hydroxide aqueous solution). Polyamide boxes and covers assembled by thermowelding. Nickel-plated copper output terminals. Sealing around the terminals is provided by preformed packings (O- Rings). Removable polyamide safety valve located in the center of the cover. Nominal capacity (C1) = 53 Ah (at the one hour discharge rate). Special characteristics Two thermostats (T1 & T2) in series with a resistor (R1) connected to the positive post of the main battery receptacle. One thermistor fitted to a special mounting plate. A series resistor (R2) connected to the negative post of the main battery receptacle. A connector receptacle located under the main connector receptacle provides electrical interface with the on board charger. Operating temperature of the thermostats T1 and T2: Open on temperature rise at 68°C (154°F). Thermistor registers 2460 Ohms at 23°C (73.4°F). R1 and R2 register 32.4K Ohms each. Temperature sensor/charge control auxiliary connector complies with MS 24264 R 12 B 12 SN 24-34-01 PAGE 2 AUG 30/96

SAFT AMERICA INC. Component Maintenance Manual 1159SCAV519-1 C. Detailed description (See Fig. 1) This comprises: a case assembly (10) complete cover (20) with an insulating gasket made of silicone elastomer bonded to the to the inner face. (a) Box (2) Storage cells The case assembly is provided with two vent pipes, four spring fasteners, and two lifting handles. An identification plate. The front face of battery P/N 1159SCAV519-1 supports the base plate of the connector receptacle connected to the temperature sensor/charge control harness assembly. (b) Cover The cover (20) is laterally provided with four catches intended for attachment to the box, and with a bar, notched at both ends, intended for battery mounting through tie-rods secured to a rack. The twenty one electrical storage cells (30) are arranged in two rows of eight and one row of five within the battery case. Each storage cell is equipped with a safety valve (120) fitted with a preformed packing (130). The storage cell terminals are made up of two threaded nickel-plated copper rods. 24-34-01 PAGE 3 AUG 30/96

P R O F E S S I O N A L - GP Batteries
P R O F E S S I O N A L - GP Batteries
SRM+ Ni-Cd batteries - Saft
SRX Ni-Cd batteries - Saft
Primary lithium battery - Saft
Saft lithium batteries
SPH Ni-Cd batteries - Saft
Primary lithium battery system - Saft
Primary lithium battery system - Saft
Ultima.plus Nickel-cadmium batteries STL +38 to STL +460 - Saft
High Power Lithium Battery Box - Saft
Primary lithium batteries LO 29 SHX - Saft
Primary lithium battery LO 34 SX - Saft
Primary lithium batteries LO 26 SXC - Saft
Primary lithium batteries LO 26 SX - Saft
Primary lithium battery LM 33550 - Saft
Rechargeable military lithium-ion battery 2 VL 34570 - Saft
Rechargeable lithium-ion battery 7s2p MP 176065 BLF - Saft
Li-SO2 primary battery system BA 5600 A/U - Saft
MSX – Ni-Cd battery Compact high power for railways - Saft
Li-SO2 primary battery system BA 5800 A/U - Saft
M -25-1 P/N 33082-002 - MarathonNorco Aerospace
M -44-8 P/N 32845-001 - MarathonNorco Aerospace