SMCBR21VPN

More documents

Recommendations

Info

WAN1 and WAN2 Interface can use Assist to enter the data. After setting, there will be two subnet in LAN: 192.168.1.0/24 (default LAN subnet) and 162.172.50.0/24. So if LAN IP is: ˙192.168.1.xx, it must use NAT Mode to access to the Internet. (In Policy it only can setup to access to Internet by WAN2. If by WAN1 Routing mode, then it cannot access to Internet by its virtual IP) ˙162.172.50.xx, it uses Routing mode through WAN1 (The Internet Server can see your IP 162.172.50.xx directly). And uses NAT mode through WAN2 (The Internet Server can see your IP as WAN2 IP)(Figure2-9) Figure 2-9 Multiple Subnet Network The SMC BR21VPN’s Interface Status: WAN1 IP: 10.10.10.1 WAN2 IP:211.22.22.22 LAN Port IP:192.168.1.1 LAN Port Multiple Subnet:162.172.50.1 37
Route Table To connect two different subnet router with the SMC BR21VPN and makes them to connect to Internet through SMC BR21VPN Preparation Company A: WAN1 (61.11.11.11) connects with ATUR to Internet WAN2 (211.22.22.22) connects with ATUR to Internet LAN subnet: 192.168.1.1/24 The Router1 which connect with LAN (10.10.10.1, support RIPv2) its LAN subnet is 192.168.10.1/24 Company B: Router2 (10.10.10.2, support RIPv2), its LAN subnet is 192.168.20.1/24 Company A ‘s Router1 (10.10.10.1) connect directly with Company B ‘s Router2 (10.10.10.2). 38
Page 1 and 2: Barricade Dual WAN Port Load Balanc
Page 3 and 4: LIMITED WARRANTY Limited Warranty S
Page 5 and 6: CONSEQUENTIAL DAMAGES FOR CONSUMER
Page 7 and 8: RFI Emission: • Limit class A acc
Page 9 and 10: Veuillez lire à fond l’informati
Page 11 and 12: Warnings and Cautionary Messages Wa
Page 13 and 14: Audience The guide is intended for
Page 15 and 16: CHAPTER 8 AUTHENTICATION ..........
Page 17 and 18: Chapter 1 Administrator Administrat
Page 19 and 20: Admin Adding a new Sub Administrato
Page 21 and 22: Add Remote Management IPs STEP 1.Ad
Page 23 and 24: Software Update STEP 1.Select Softw
Page 25 and 26: Define the required fields of Setti
Page 27 and 28: NAT Mode: It allows Internal Netwo
Page 29 and 30: Setting System Settings- Exporting
Page 31 and 32: Restoring Factory Default Settings
Page 33 and 34: Enabling E-mail Alert Notification
Page 35 and 36: Date / Time Date/Time Settings STEP
Page 37: Adding Multiple Subnet Add the foll
Page 41 and 42: STEP 3.Enter the following setting
Page 43 and 44: DHCP STEP 1.Select DHCP in System a
Page 45 and 46: DDNS Dynamic DNS Settings STEP 1.Se
Page 47 and 48: Host Table STEP 1.Select Host Table
Page 49 and 50: Chapter 3 Interface Interface In th
Page 51 and 52: Connect Mode: Display the current
Page 53 and 54: We set up four Interface Address ex
Page 55 and 56: WAN Setting WAN Interface Address S
Page 57 and 58: STEP 3.Select the Connecting way:
Page 59 and 60: Dynamic IP Address (Cable Modem Use
Page 61 and 62: Static IP Address (Figure3-9) 1. Se
Page 63 and 64: DMZ Setting DMZ Interface Address (
Page 65 and 66: Chapter 4 Address Address The SMC B
Page 67 and 68: We set up two Address examples in t
Page 69 and 70: STEP 2.Adding the following setting
Page 71 and 72: Setup a policy that only allows par
Page 73 and 74: STEP 3.Enter the following settings
Page 75 and 76: Chapter 5 Service Service TCP and U
Page 77 and 78: Define the required fields of Servi
Page 79 and 80: Custom Allow external user to commu
Page 81 and 82: Under general circumstances, the ra
Page 83 and 84: Group Setting service group and res
Page 85 and 86: STEP 2.In LAN Group of Address func
Page 87 and 88: Example To configure the valid time
Page 89 and 90:
Chapter 7 QOS QoS By configuring th
Page 91 and 92:
Define the required fields of QoS W
Page 93 and 94:
Example Setting a policy that can r
Page 95 and 96:
Chapter 8 Authentication Authentica
Page 97 and 98:
When the user connect to external n
Page 99 and 100:
Auth-User Name: The user account f
Page 101 and 102:
Example Setting specific users to c
Page 103 and 104:
STEP 3.Add a policy in Outgoing Pol
Page 105 and 106:
Chapter 9 Content Blocking Content
Page 107 and 108:
Sub-name file Blocking: Prevent us
Page 109 and 110:
URL Restrict the Internal Users onl
Page 111 and 112:
STEP 2.Add a Outgoing Policy and us
Page 113 and 114:
STEP 2.Add a new Outgoing Policy an
Page 115 and 116:
STEP 2.Add a new Outgoing Policy an
Page 117 and 118:
Step2. In Policy Outgoing, add one
Page 119 and 120:
Chapter 10 Virtual Server Virtual S
Page 121 and 122:
Define the required fields of Virtu
Page 123 and 124:
Example Make a single server that p
Page 125 and 126:
STEP 7.Complete the setting of prov
Page 127 and 128:
STEP 2.Enter the following data in
Page 129 and 130:
The external user use VoIP to conne
Page 131 and 132:
STEP 5.Add a new Incoming Policy, w
Page 133 and 134:
Make several servers that provide s
Page 135 and 136:
STEP 4.Enter the following data in
Page 137 and 138:
STEP 7.Complete the setting of prov
Page 139 and 140:
Define the required fields of VPN:
Page 141 and 142:
Define the required fields of IPSec
Page 143 and 144:
Define the required fields of PPTP
Page 145 and 146:
We set up two VPN examples in this
Page 147 and 148:
STEP 4.Select Preshare in Authentic
Page 149 and 150:
STEP 9.Enter the following setting
Page 151 and 152:
Page 153 and 154:
STEP 4.Select Remote Gateway-Fixed
Page 155 and 156:
Page 157 and 158:
Page 159 and 160:
Setting PPTP VPN connection between
Page 161 and 162:
STEP 2.Add the following settings i
Page 163 and 164:
Page 165 and 166:
The Default Gateway of Company B is
Page 167 and 168:
Page 169 and 170:
STEP 5.Complete PPTP VPN Connection
Page 171 and 172:
(4) LAN to DMZ: The source IP is in
Page 173 and 174:
Option: To display if every functi
Page 175 and 176:
We set up six Policy examples in th
Page 177 and 178:
STEP 2.Complete the setting of Logg
Page 179 and 180:
Forbid the users to access to speci
Page 181 and 182:
STEP 2.Enter as following in WAN an
Page 183 and 184:
Page 185 and 186:
Page 187 and 188:
STEP 3.Enter the following in Incom
Page 189 and 190:
STEP 4.Enter the following in WAN t
Page 191 and 192:
Page 193 and 194:
STEP 8.Add the following setting in
Page 195 and 196:
Define the required fields of Hacke
Page 197 and 198:
Detect Ping of Death Attack: Selec
Page 199 and 200:
Internet Alert SMC BR21VPN Alarm an
Page 201 and 202:
Figure16-4 NetBIOS Alert Notificati
Page 203 and 204:
Chapter 14 Attack Alarm Attack Alar
Page 205 and 206:
Internal Alarm To record the DDoS a
Page 207 and 208:
STEP 2.When Hacker attacks the SMC
Page 209 and 210:
We set up four LOG examples in the
Page 211 and 212:
STEP 3.Click Traffic Log. It will s
Page 213 and 214:
STEP 5.Click on Download Logs and s
Page 215 and 216:
Event Log To record the detailed ma
Page 217 and 218:
STEP 3.Click Clear Logs and click O
Page 219 and 220:
STEP 2.Click on Download Logs and s
Page 221 and 222:
Log Backup To save or receive the r
Page 223 and 224:
Chapter 16 Accounting Report Accoun
Page 225 and 226:
Inbound Accounting Report It is the
Page 227 and 228:
Figure19-1 Outbound Source IP Stati
Page 229 and 230:
Figure19-2 Outbound Destination IP
Page 231 and 232:
Accounting Report. 230
Page 233 and 234:
Inbound STEP 1.Enter Inbound in Acc
Page 235 and 236:
Enter Inbound in Accounting Report
Page 237 and 238:
STEP 2.Enter Inbound in Accounting
Page 239 and 240:
Chapter 17 Statistics Statistics WA
Page 241 and 242:
WAN Statistics STEP 1.Enter WAN in
Page 243 and 244:
Policy Statistics STEP 1.If you had
Page 245 and 246:
Chapter 18 Status Status The users
Page 247 and 248:
Figure21-1 Interface Status 246
Page 249 and 250:
ARP Table STEP 1.Enter ARP Table in
Page 251:
20 Mason • Irvine, CA 92618 • P
show all

SMCBR21VPN

You also want an ePaper? Increase the reach of your titles

Delete template?

Save as template?