Library manual XBTGC Expert I/O High speed counting | 3 MB

More documents

Recommendations

Info

Chapter 7 Functions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 53 HMI_HSCStart: Start the HSC. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 54 HMI_HSCStop: Stop the HSC . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 55 HMI_HSCGetCurrentValue: Get the HSC Current Value . . . . . . . . . . . . 56 HMI_HSCGetCapturedValue: Get the HSC Value . . . . . . . . . . . . . . . . . 57 HMI_GetSynchronizedOutput: Get Synchronized Output Status . . . . . . 58 HMI_ClearSynchronizedOutput: Clear Synchronized Output Status. . . . 59 HMI_SetCounterValue: Set the HSC Value. . . . . . . . . . . . . . . . . . . . . . . 60 HMI_ClearCounterValue: Clear the HSC Value . . . . . . . . . . . . . . . . . . . 61 HMI_GetPreLoadStatus: Detect Preload Input Signal. . . . . . . . . . . . . . . 62 HMI_ClearPreLoadStatus: Clear PreLoad Status . . . . . . . . . . . . . . . . . . 63 HMI_GetPreStrobeStatus: Get PreStrobe Status . . . . . . . . . . . . . . . . . . 64 HMI_ClearPreStrobeStatus: Clear PreStrobe Status . . . . . . . . . . . . . . . 65 HMI_GetMarkerStatus: Detect Hardware Marker Input Signal . . . . . . . . 66 HMI_ClearMarkerStatus: Clear the Marker Status . . . . . . . . . . . . . . . . . 67 Appendices . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 69 Appendix A Function and Function Block Representation . . . . . . . . 71 Differences Between a Function and a Function Block . . . . . . . . . . . . . . 72 How to Use a Function or a Function Block in IL Language . . . . . . . . . . 73 How to Use a Function or a Function Block in ST Language . . . . . . . . . 76 Glossary . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 79 Index . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 87 4 04/2012
Important Information NOTICE Safety Information Read these instructions carefully, and look at the equipment to become familiar with the device before trying to install, operate, or maintain it. The following special messages may appear throughout this documentation or on the equipment to warn of potential hazards or to call attention to information that clarifies or simplifies a procedure. 04/2012 5 §
Page 1 and 2: EIO0000000644.04 Magelis XBT GC HMI
Page 3: Table of Contents Safety Informatio
Page 7 and 8: At a Glance Document Scope Validity
Page 9 and 10: User Comments UNINTENDED EQUIPMENT
Page 11 and 12: Magelis XBT GC HMI Controller I/O C
Page 13 and 14: Introduction Magelis XBT GC HMI Con
Page 15 and 16: Local I/Os and Special I/Os Configu
Page 17 and 18: Special I/O Case 2: One 2-Phase HSC
Page 19 and 20: I/O Summary Overview Special I/O Th
Page 21 and 22: Special I/O Example of I/O Summary
Page 25 and 26: Magelis XBT GC HMI Controller HSC O
Page 27 and 28: HSC Overview Once the HSC is config
Page 29 and 30: General Magelis XBT GC HMI Controll
Page 31 and 32: Up/Rising Edge Counter Mode 1-Phase
Page 33 and 34: Up/Falling Edge Counter Mode 1-Phas
Page 35 and 36: Specifications 1-Phase HSC Specific
Page 37 and 38: General Magelis XBT GC HMI Controll
Page 39 and 40: Mode 0 2-Phase HSC Counter Mode 0 D
Page 41 and 42: Mode 2 2-Phase HSC Counter Mode 2 D
Page 43 and 44: Specifications 2-Phase HSC Specific
Page 45 and 46: Magelis XBT GC HMI Controller HSC C
Page 47 and 48: I/O Summary HSC Configuration Param
Page 51 and 52: Magelis XBT GC HMI Controller Gener
Page 53 and 54: Overview Magelis XBT GC HMI Control
Page 55 and 56:
HMI_HSCStop: Stop the HSC Function
Page 57 and 58:
HMI_HSCGetCapturedValue: Get the HS
Page 59 and 60:
HMI_ClearSynchronizedOutput: Clear
Page 61 and 62:
HMI_ClearCounterValue: Clear the HS
Page 63 and 64:
HMI_ClearPreLoadStatus: Clear PreLo
Page 65 and 66:
HMI_ClearPreStrobeStatus: Clear Pre
Page 67 and 68:
HMI_ClearMarkerStatus: Clear the Ma
Page 69 and 70:
Magelis XBT GC HMI Controller 04/20
Page 71 and 72:
Overview Magelis XBT GC HMI Control
Page 73 and 74:
How to Use a Function or a Function
Page 75 and 76:
Step Action Function and Function B
Page 77 and 78:
Function and Function Block Represe
Page 79 and 80:
1-phase counter 2-phase counter BOO
Page 81 and 82:
expansion bus E Glossary The expans
Page 83 and 84:
Modbus NEMA PLC PLI POU PTO M The M
Page 85 and 86:
U unlocated variable An unlocated v
Page 87 and 88:
Magelis XBT GC HMI Controller Index
show all

Library manual XBTGC Expert I/O High speed counting | 3 MB

You also want an ePaper? Increase the reach of your titles

Delete template?

Save as template?