Library manual XBTGC Expert I/O High speed counting | 3 MB

More documents

Recommendations

Info

HSC Configuration HSC Configuration Screen The following screenshot shows the entire HSC configuration screen: Properties of the HSC Configuration Screen The following table describes the properties of the HSC Configuration screen: Parameters Initial Value Range Description Phase Type Not used Not Used Select the HSC counter 1-Phase 2-Phase 1 HSC 2-Phase 2 HSC type 46 04/2012
I/O Summary HSC Configuration Parameters Initial Value Range Description IN (2n+1) Not used Not Used Normal Input Preload Prestrobe Select the input pin type Out(n) Not used Normal Ouput Synchronized Output Select the ouput pin type Mode (1-Phase) Up/Rising Up/Rising edge Counter Select the 1-Phase HSC Edge Down/Rising edge Counter Up/Falling edge Counter Down/Falling edge Counter counter mode Mode (2-Phase) Mode 0 Mode 0 Select the 2-Phase HSC Mode 1 Mode 2 Mode 3 counter mode On Preload 1000 0 - 4,294,967,295 Set the On Preload value On Preset 2000 0 - 4,294,967,295 Set the On Preset value Off Preset 2000 0 - 4,294,967,295 Set the Off Preset value When selecting HSC → Counter Type → Phase Type as 1-Phase HSC counter from the I/O Configuration window, you can configure: Each of the four HSC groups as 1-Phase HSC counter When selecting HSC → Counter Type → Phase Type as a 2-Phase 1 HSC from the I/O Configuration window: Group 0 (HSC00) and 1 (HSC01) form a 2-Phase HSC counter Group 2 (HSC02) and 3 (HSC03) can be configured as 1-Phase HSC counter When selecting HSC → Counter Type → Phase Type as a 2-Phase 2 HSC from the I/O Configuration window: Group 0 (HSC00) and 1 (HSC01) form a 2-Phase HSC counter Group 2 (HSC02) and 3 (HSC03) form another 2-Phase HSC counter The I/O Summarize... button is described in the I/O Summary (see page 19) section. 04/2012 47
Page 1 and 2: EIO0000000644.04 Magelis XBT GC HMI
Page 3 and 4: Table of Contents Safety Informatio
Page 5 and 6: Important Information NOTICE Safety
Page 7 and 8: At a Glance Document Scope Validity
Page 9 and 10: User Comments UNINTENDED EQUIPMENT
Page 11 and 12: Magelis XBT GC HMI Controller I/O C
Page 13 and 14: Introduction Magelis XBT GC HMI Con
Page 15 and 16: Local I/Os and Special I/Os Configu
Page 17 and 18: Special I/O Case 2: One 2-Phase HSC
Page 19 and 20: I/O Summary Overview Special I/O Th
Page 21 and 22: Special I/O Example of I/O Summary
Page 25 and 26: Magelis XBT GC HMI Controller HSC O
Page 27 and 28: HSC Overview Once the HSC is config
Page 29 and 30: General Magelis XBT GC HMI Controll
Page 31 and 32: Up/Rising Edge Counter Mode 1-Phase
Page 33 and 34: Up/Falling Edge Counter Mode 1-Phas
Page 35 and 36: Specifications 1-Phase HSC Specific
Page 37 and 38: General Magelis XBT GC HMI Controll
Page 39 and 40: Mode 0 2-Phase HSC Counter Mode 0 D
Page 41 and 42: Mode 2 2-Phase HSC Counter Mode 2 D
Page 43 and 44: Specifications 2-Phase HSC Specific
Page 45: Magelis XBT GC HMI Controller HSC C
Page 51 and 52: Magelis XBT GC HMI Controller Gener
Page 53 and 54: Overview Magelis XBT GC HMI Control
Page 55 and 56: HMI_HSCStop: Stop the HSC Function
Page 57 and 58: HMI_HSCGetCapturedValue: Get the HS
Page 59 and 60: HMI_ClearSynchronizedOutput: Clear
Page 61 and 62: HMI_ClearCounterValue: Clear the HS
Page 63 and 64: HMI_ClearPreLoadStatus: Clear PreLo
Page 65 and 66: HMI_ClearPreStrobeStatus: Clear Pre
Page 67 and 68: HMI_ClearMarkerStatus: Clear the Ma
Page 69 and 70: Magelis XBT GC HMI Controller 04/20
Page 71 and 72: Overview Magelis XBT GC HMI Control
Page 73 and 74: How to Use a Function or a Function
Page 75 and 76: Step Action Function and Function B
Page 77 and 78: Function and Function Block Represe
Page 79 and 80: 1-phase counter 2-phase counter BOO
Page 81 and 82: expansion bus E Glossary The expans
Page 83 and 84: Modbus NEMA PLC PLI POU PTO M The M
Page 85 and 86: U unlocated variable An unlocated v
Page 87 and 88: Magelis XBT GC HMI Controller Index

Library manual XBTGC Expert I/O High speed counting | 3 MB

You also want an ePaper? Increase the reach of your titles

Delete template?

Save as template?