Powertool Systems - psm-muenchen.de

More documents

Recommendations

Info

PSM21 Maintenance and use of the tool General remarks on operation of compressed air tools Powertool Systems Instructions for the PSM21 drill feed unit Service and maintenance work on the compressed air tools must be carried out correctly by experienced and skilled employees. Cleaning and checking the tool every 1000 operating hours is recommended. If any vibrations, unusual noises, changes in speed or irregularities are noticed, do not continue using the tool and switch it off. It makes sense to clean the filter element in the tool‘s compressed air connection to avoid the later becoming blocked and thus preventing a reduction in the motor output. If the tool does not start after a long period at a standstill, place a few drops of oil (Art. No. 99011001) in the compressed air connections and repeat the start procedure. Always cut off the tool from the source of compressed air before any accessories are replaced, serviced or dismantled. Following every intervention for maintenance, test the tools in order to check their rate of advance and functionality. The spare parts list is sent separately for general information. It is only intended for the staff responsible. Only use original PSM spare parts. (The guarantee rights become invalid if components are used that are not original parts). Repairs that are not conducted correctly may cause accidents. In order to avoid accidents as a result of any unsuitable applications and to enjoy the best performances from the tool and a comprehensive customer service, repairs or maintenance work must always be conducted by the PSM Technical Customer Service, Fraunhoferstrasse 11a, D-8 15 Martinsried – or by an authorised service centre in your own country. The PSM Technical Customer Service can also organise courses on the correct use and proper conduct of maintenance and repairs of PSM products on request. Disposal of used appliances This compressed air tool is made largely of aluminium, steel, cast iron, brass and plastic. All the components can be easily disposed of, and they are neither environmental nor health hazards. Sort the individual parts according to their materials for recycling or separate disposal. Where applicable, PSM will take back individual parts that have been dismantled and sorted according to their materials. Packaging materials PSM products are packed in maerials made from recovered paper and plastics, which can be recycled. The packaging material meets the regulations of European Directive 94/ /EEC. Statutory provisions 1.7.1. Richtlinien Directive 98/37 EC - Safety of machinery. 1.7. . Technische Normen EN 292-1:1991 Safety of machinery. Basic concepts, general principles for design. Part 1: Basic terminology, methodology. EN 292-2:1991 Safety of machinery. Basic concepts, principles for design. Part : Technical principles and specifications. EN 792:2000 Hand-held non-electric power tools. Safety requirements. Part 1- 1 . EN 12096:1997 Mechanical vibration - Declaration and verification of vibration emission values. EN 28662-1:1992 Hand-held portable power tools - Measurement of vibrations at the handle. Part 1: General. EN ISO 8662-4:1995 Hand-held portable power tools - Measurement of vibrations at the handle. Part 4: Grinders. EN ISO 8662-7:1997 Hand-held portable power tools - Measurement of vibrations at the handle. Part 7:Wrenches, screwdrivers and nutrunners with impact, impulse or ratchet action. EN ISO 8662-8:1997 Hand-held portable power tools - Measurement of vibrations at the handle – Part 8: Polishers and rotary, orbital and random orbital sanders. EN ISO 8662-13:1997 Handheld portable power tools - Measurement of vibrations at the handle. Part 13: Die grinders. EN ISO 3744:1995 Acoustics.Determination of sound power levels of noise sources using sound pressure. Engineering method in an essentially free field over a reflecting plane. EN ISO 15744:2002 Hand-held non-electric power tools. Noise measurement code. Engineering method (grade ). EN ISO 4871:1996 Acoustics - Declaration and verification of noise emission values of machinery and equipment. ISO 2787:1984 Rotary and percussive pneumatic tools. Performance tests. EN ISO 5349-1:2001 Mechanical vibration. Measurement and evaluation of human exposure to hand - transmitted vibration. Part 1: General requirements. EN ISO 5349-2:2001 Mechanical vibration. Measurement and evaluation of human exposure to hand - transmitted vibration. Part : Practical guidance for measurement at the workplace. ISO 5393:1994 Rotary tools for threaded fasteners. Performance test method. ISO 6544:1981 Hand-held pneumatic assembly tools for installing threaded fasteners - Reaction Torque and Torque Impulse Measurements. CR 1030-1:1995 Hand-arm vibration – Guidelines for vibration hazards reduction – Part 1: Engineering methods by design of machinery. CR 1030-2:1995 Hand-arm vibration – Guidelines for vibration hazards reduction – Part : Management measures at the workplace. PSM Powertool Systems Manglitz GmbH, Fraunhoferstrasse 11a, 82152 Martinsried, Germany, Tel. +49 (0)89 899621-0, Fax +49 (0)89 899621-30 www.psm-muenchen.de - Page 1 -
Functional description Powertool Systems Instructions for the PSM21 drill feed unit PSM21 Special notes on function and operation Within the enclosure there are a double-acting compressed air cylinder (A), a sleeve (B), in which a compressed air drive motor (44, 43) is situated, as well as the motor cut-off valve (C). There are three compressed air connections on the rear. Connection (49) acts upon the compressed air motor, connection (50) acts upon the prestroke and return stroke. At the starting and end position, the motor supply air is closed by the internal motor cut-off valve (C). As soon as the connection (50, on the right) is activated and the compressed air cylinder traverses forward, the motor cut-off valve (C) will be opened after a stroke of mm and the motor will then start up. The sleeve now moves to the set drilling depth. By activating the connection (50, left) the sleeve will move to its final/starting position and the motor will be switched on. The overall stroke length is set with the stroke setting screw ( ), the length of the working stroke with the internal adjusting screw (13) in ( ). PSM Powertool Systems Manglitz GmbH, Fraunhoferstrasse 11a, 82152 Martinsried, Germany, Tel. +49 (0)89 899621-0, Fax +49 (0)89 899621-30 www.psm-muenchen.de - Page 13 -
Page 1 and 2: Operating Instructions Spare Parts
Page 3 and 4: Index General Design General techni
Page 5 and 6: PSM21 Construction of the PSM21 Pow
Page 7 and 8: PSM21 Scale drawings Dimensions of
Page 9 and 10: PSM21 Examples of a pneumatic contr
Page 11: PSM21 General remarks on operation
Page 15 and 16: Powertool Systems Instructions for
Page 17 and 18: PSM21 Drawings and spare parts list
Page 19 and 20: PSM21 Drawings and spare parts list

Powertool Systems - psm-muenchen.de

You also want an ePaper? Increase the reach of your titles

Delete template?

Save as template?