PT-DZ6710E PT-DZ6700E PT - Panasonic Business
PT-DZ6710E PT-DZ6700E PT - Panasonic Business
PT-DZ6710E PT-DZ6700E PT - Panasonic Business
Create successful ePaper yourself
Turn your PDF publications into a flip-book with our unique Google optimized e-Paper software.
Maintenance<br />
Monitor Lamp indicators<br />
Managing the indicated problems<br />
If a problem should occur with the projector, the indicators will inform you. Manage the indicated problems as follow.<br />
1. Confirm the status of all indicators and projector, and switch off the projector in proper way.<br />
2. Find out the cause of the problem by status of each indicator.<br />
3. Follow the instruction for each indication below and solve the problem.<br />
4. Turn on the projector in the correct way and confirm the indicator is not indicating a problem any longer.<br />
NOTE:<br />
• If no problem is found or the problem remains, do not turn on the projector. Instead contact your nearest dealer.<br />
LAMP1/LAMP2 indicator<br />
Lamp<br />
indication<br />
Lighting in red<br />
Blinking in red<br />
once<br />
Blinking in red<br />
3 times<br />
TEMP indicator<br />
Lamp<br />
indication<br />
Lighting in red<br />
Blinking in red<br />
once<br />
Blinking in red<br />
twice<br />
Blinking in red<br />
3 times<br />
ENGLISH - 28<br />
Indicators<br />
Power indicator<br />
Lamp1 (LAMP1) indicator<br />
Lamp2 (LAMP2) indicator<br />
Temperature (TEMP) indicator<br />
Filter (FILTER) indicator<br />
STANDBY(RED)/<br />
ON(GREEN)<br />
Information Check point Remedial measure<br />
Indicates the time for<br />
replacing the lamp unit<br />
Lamp unit is not installed.<br />
Error is detected in the<br />
lamp circuit.<br />
• Did you notice a “REPLACE<br />
LAMP” message on the screen<br />
when turning on the projector<br />
power supply?<br />
• Check the lamp unit<br />
compartment.<br />
• Did you turn the power back on<br />
immediately after turning it off?<br />
• Some error has arisen in the<br />
lamp circuit.<br />
• Check for fluctuation (or drop) in<br />
the source voltage.<br />
• This lamp monitor lights up when the lamp<br />
unit used hours have reached 1 800* hours.<br />
Request the dealer to replace the lamp unit.<br />
* 2 800 hours for <strong>PT</strong>-D5000E only.<br />
• Install the lamp unit.<br />
• When lamp unit is installed and still having<br />
the indicator lights, contact to the dealer.<br />
• Wait until the lamp has cooled off, and then<br />
turn on the power.<br />
• Turn off the POWER switch of the projector<br />
properly and contact your nearest dealer.<br />
Information Check point Remedial measure<br />
Warm-up status<br />
LAMP TEMP FILTER<br />
High temperature inside.<br />
(WARNING)<br />
The filter is excessively<br />
dirty and the ventilation is<br />
poor.<br />
High temperature inside.<br />
(Standby condition)<br />
Cooling fan has been<br />
stopped.<br />
STANDBY(RED)/<br />
ON(GREEN)<br />
LAMP TEMP FILTER<br />
• Did you turn on the power when<br />
the ambient temperature was<br />
lower than approx. 0 °C (32 °F)?<br />
• Check the ventilation port is<br />
blocked.<br />
• Is the room air temperature too<br />
high?<br />
• Was the temperature warning<br />
indication displayed?<br />
• Wait about 5 minutes in the current status.<br />
• Install the unit in a location having an<br />
ambient temperature from 0 °C (32 °F) -<br />
45 °C (113 °F).<br />
• Remove the object that is blocking the<br />
ventilation port.<br />
• Move the projector to a temperature of 0 °C<br />
(32 °F) - 45 °C (113 °F) and the humidity of<br />
20 % to 80 % (no condensation).<br />
• Turn off the POWER switch of the projector<br />
in proper way and contact the dealer.<br />
• Turn off the POWER switch of the projector<br />
in proper way and contact the dealer.