MEMORANDUM TO: Holders of Contracts Documents FROM: Karen ...
MEMORANDUM TO: Holders of Contracts Documents FROM: Karen ...
MEMORANDUM TO: Holders of Contracts Documents FROM: Karen ...
Create successful ePaper yourself
Turn your PDF publications into a flip-book with our unique Google optimized e-Paper software.
14.4 All joints in floor covering shall be butt-cut type. The pieces shall meet flush in order to avoid water<br />
seepage. Floor covering shall be bonded to the floor with waterpro<strong>of</strong> sealer.<br />
14.5 Steps shall be sloped only enough to preclude water accumulation in the stepwell. Step treads and<br />
exposed vertical risers shall be <strong>of</strong> matching colored material, with integrally molded nosing, and be<br />
consistent with the passenger area.<br />
14.6 A permanent two (2) inch wide, full width, bright yellow or white band shall mark the edge <strong>of</strong> each<br />
step. The colors shall be permanently blended into the tread covering material. Each tread shall be<br />
completely sealed around the edges with a waterpro<strong>of</strong> rubber sealant.<br />
14.7 A stepwell low voltage electric heater pad, such as Ultra Heat SH-267 or Lighthouse Warm<br />
Welcome, or approved equal, shall be installed on the first step beneath the floor covering <strong>of</strong> the initial<br />
step to eliminate ice and snow build-up.<br />
14.8 The top surface <strong>of</strong> any wheelchair securement floor plates shall not constitute a tripping hazard<br />
and meet all state and federal guidelines.<br />
14.9 Deleted.<br />
15 MIRRORS<br />
15.1 Two (2) fully adjustable, Rosco, Lucerix/Metagal, B&R or approved equal, exterior left side/right<br />
side, side view mirrors shall be provided. Each head shall incorporate replaceable mirrors including: a 9 x<br />
7 inch flat mirror (minimum), and a separate 4 x 6 inch (minimum) convex mirror. The convex mirror<br />
shall be located below the flat glass mirror so as to allow for increased driver visibility along both sides<br />
<strong>of</strong> the vehicle. The mirror housing shall be molded and feature one point mounting, so as to provide an<br />
undistorted view <strong>of</strong> the rear corners <strong>of</strong> the vehicle. The mirrors shall be heated and remote controlled,<br />
with an LED turn signal in the mirror that can be viewed from behind the bus.<br />
15.2 Mirror brackets are to be made from carbon tubing or anodized cast aluminum, black in color.<br />
Brackets shall be spring-loaded, feature single point mounting and be designed to fold out <strong>of</strong> the way<br />
without damage to the mirrors or vehicle body upon contact with an obstruction or when met with<br />
resistance.<br />
15.3 The left side mirror shall be mounted on the driver’s door and be electrically and remotely<br />
adjustable. The right side mirror shall be electrically and remotely operated. The right side mirror shall<br />
be fender mounted and braced from behind the fender with a stiffening plate, <strong>of</strong> a material which does<br />
not contribute to galvanic corrosion.<br />
15.4 Interior mirror(s) shall be placed so as to allow the driver to observe passengers throughout the<br />
vehicle without leaving his/her seat and without shoulder movement. With a full load, the driver shall be<br />
able to observe passengers anywhere in the bus, including the rear wheelchair area, rear seats and<br />
anywhere in the aisle via a minimum 6” X 16” mirror that shall be mounted in front and over the driver.<br />
In addition, a minimum 3”x 9” rectangular rearview mirror, OEM’s standard chassis rearview mirror with<br />
non-glare day/night feature as located by the OEM or approved equal, shall be installed in the middle <strong>of</strong><br />
and on the front windshield for driver’s view <strong>of</strong> and through bus interior. The location <strong>of</strong> the interior<br />
mirrors shall be approved by the MTA at the PDR and shall be consistent throughout each build.<br />
16 DOORS<br />
16.1 The vehicle shall be equipped with four (4) doors: A passenger entrance door with steps on the<br />
curbside front, a driver’s entrance door on the roadside front, rear door(s) for use as an emergency exit,<br />
and a minimum 42 inch wide wheelchair lift service door on the curbside <strong>of</strong> the vehicle. If the vehicle is<br />
PAGE 14 OF 40