Operating and Installation Instructions Fridge/freezer ... - Miele.ca

More documents

Recommendations

Info

$S:\Tech Writing\Data\Cooktop\us\vp\KM5840_us.vp - Miele.ca$

Aligning the appliance doors The appliance doors can be aligned with the appliance housing afterwards. In the following figure, the appliance door is not closed so that the individual steps can be seen more clearly. Align the bottom door in the bottom hinge bracket via the outer, elongated holes: Remove the middle screw from the hinge bracket. Loosen the two outer screws slightly. Align the appliance door by moving the hinge bracket to the right or left. Tighten the screws ; the screw does not need to be screwed on again. 66 Align the top door via the elongated holes in the middle hinge bracket: Loosen the three screws slightly. Align the appliance door by moving the hinge bracket to the right or left. Tighten the screws .
adapter cabinet appliance kitchen cabinet wall The appliance can be installed in any fitted kitchen. To match the appliance to the height of the fitted kitchen, a suitable adapter cabinet can be installed over the appliance. A ventilation gap of at least 2 inches (50 mm) must be provided between the adapter cabinet and the kitchen wall. The ventilation cross-section below the room ceiling must be at least 46 in2 (300 cm2 ) so that warm air can escape without obstruction. Otherwise the appliance has to work harder, which results in increased energy consumption. Installing the appliance The ventilation cross-sections must not be blocked or covered in any way. They also need to be dusted/cleaned on a regular basis. If installing with standard kitchen cabinets (max. depth 580 mm), the appliance can be set up directly next to the kitchen cabinet. In that case the side of the appliance door would project 34 mm and the middle of the appliance 55 mm beyond the front of the kitchen cabinet. This allows the appliance door to open and close properly. If the appliance is installed next to a wall , a gap of at least 55 mm is needed on the hinge side between the wall and the appliance . This allows space for the handle when the door is open. 67
Page 1 and 2:
Operating and Installation Instruct
Page 3 and 4:
Contents Freezing and storing food.
Page 5 and 6:
ON button for the whole appliance a
Page 7 and 8:
Disposal of packing materials The c
Page 9 and 10:
Technical safety Before setting up
Page 11 and 12:
The manufacturer will not be held l
Page 13 and 14:
How to save energy Normal energy co
Page 15 and 16: Use this button to switch back and
Page 17 and 18: The door alarm is automatically dis
Page 19 and 20: The correct temperature is very imp
Page 21 and 22: Changing the brightness of the temp
Page 23 and 24: Door alarm If one of the appliance
Page 25 and 26: Super Freeze For best results, swit
Page 27 and 28: Different storage zones Due to the
Page 29 and 30: Moving the serving shelf / bottle s
Page 31 and 32: Maximum freezing capacity To ensure
Page 33 and 34: Before placing food in the freezer
Page 35 and 36: For the automatic ice cube maker to
Page 37 and 38: By tapping the button you can now
Page 39 and 40: Never use abrasive cleaners on the
Page 41 and 42: Door seal Do not use any grease or
Page 43 and 44: If you changed the active charcoal
Page 45 and 46: . . . the frozen food thaws because
Page 47 and 48: Pull out the glass plate. Unscrew
Page 49 and 50: In the event of a fault which you c
Page 51 and 52: Attach the stainless steel hose to
Page 53 and 54: Do not place any devices that produ
Page 55 and 56: Appliance dimensions Installation i
Page 57 and 58: Before changing the hinging, remove
Page 59 and 60: Caution! The top door of the applia
Page 61 and 62: Lift the plugs out of the door bea
Page 63 and 64: Hang the panel on the shock absorb
Page 65: Remove the securing device . Place
show all

Operating and Installation Instructions Fridge/freezer ... - Miele.ca

Create successful ePaper yourself

Delete template?

Save as template?