TASKI Jontec TimeSaver Ultra High Performance Floor Emulsion

TASKI Jontec TimeSaver
Ultra high performance floor emulsion
Description
Jontec TimeSaver is a ultra high gloss, high performance floor emulsion for
most type of smooth and water resistant, hard floors. Its very low odour makes it
ideal for public hallways, patient’s room, retail and 24 hour facilities.
Specially formulated with an ultra high level of solids of a unique Johnson
Polymer, Jontec TimeSaver provides superior gloss level than standard floor
emulsions, even with fewer coats. Despite the very high level of solids, it does
not require a special applicator or equipment and the protection offers
exceptional resistance to scratching, scuffing and black heel marks. Therefore
provides a better appearance over time, even with less maintenance. The high
resistance to scratches also extends the lifetime before full stripping and
recoating operation. And for even more savings, a top stripping and recoating
operation with only one recoat will allow you to extend the lifetime of the
protection even more significantly. You save time on application, time on
maintenance and time before full stripping.
Key properties
• Ultra high solids, unique polymer
• Higher gloss level with fewer coats
• Superior resistance to black heel marks and scratches
• Low odour
• Opaque white emulsion
Benefits
• Defines a new category of floor emulsion
• Saves time during application while leaving a much nicer finish
• Maintains the better appearance over time, requires less maintenance
and extends lifetime of the protection significantly
• Perfect for open and public areas
• Ideal application to avoid missed spots and to leave a crystal clear finish
F2n

TASKI Jontec TimeSaver
Use instructions
Dosage: Ready to use. Apply undiluted.
Application:
Preparation: Strip the floor with a JohnsonDiversey floor stripper, rinse thoroughly and allow the floor to fully dry.
Using Jontec ProStrip (and Jontec LinoSafe L on linoleum) is strongly recommended for maximum efficiency.
The use of other floor strippers will require considerably more efforts and time.
Application: Sparingly pour product onto the floor and evenly spread it while still wet with a polish applicator in
overlapping lanes of 1-1.5m. Allow to dry completely (20-30 minutes) before applying additional coats in similar
manner. The white appearance of Jontec TimeSaver during application allows you to visually locate and avoid
missed spots. Application marks will disappear when drying. Two coats will usually be sufficient on most types of
floors. On non-homogenous floors (e.g. Stone, Terrazzo, Linoleum) apply one coat of an appropriate sealer prior
to application of JontecTimeSaver. It is recommended to allow the protection to cure 24 hours and then dry buff
the floor once in order to densify the film and improve the slip resistance of the protection.
Top stripping and recoating: In order to extend lifetime of the protection, a top stripping and recoating using only
1 coat of Jontec TimeSaver will allow you to gather additional months of protection. Use one of the
JohnsonDiversey’s floor top strippers to remove one coat of polish, allow drying completely and apply one coat
of Jontec TimeSaver. Your protection will look again like new! This allows you to extend the periods between
full stripping operations.
Technical data
• Appearance: cloudy, white liquid
• Relative density [20°C]: 1.04
• pH-value neat: 7.5 - 8.0
Safe handling and storage information
Safe handling:
Full guidance on the handling and disposal of this product is provided in a separate Material Safety Data Sheet.
Only for professional users / specialists.
Storage Information:
Store in original closed containers and do not store at temperatures below 5°C
Approvals
Tested according to ASTM D-2047 for slip resistance
JohnsonDiversey European
Headquarters, WTC Amsterdam
Airport, Tower B, 8th Floor Schipol
Boulevard 209, Luchthaven Schipol, The
Netherlands 1118 BH
www.johnsondiversey.com
P92560XFEN-02 © Copyright 2006 JohnsonDiversey 2