Pro H50/55-Series Gas Fryers Service and Parts Manual - Frymaster

More documents

Recommendations

Info

2. Remove the blower motor shield and separate the blower motor from the housing as shown in the illustration on the following page. Remove these screws to remove the shield from the blower assembly. 1-11 Remove these nuts to separate the blower motor from the housing. 3. Wrap the motor with plastic wrap to prevent water from entering it. Spray degreaser or detergent on the blower wheel and the blower housing. Allow it to soak for five minutes. Rinse the wheel and housing with hot tap water, then dry with a clean cloth. Wrap the motor and wires with plastic wrap or a plastic bag. Blower Wheel Blower Housing 4. Remove the plastic wrap from the blower motor assembly. Reassemble the blower motor assembly and blower housing. Reinstall the blower shield. 5. Reinstall the blower assembly in the fryer and reconnect the wiring disconnected in Step 1.
6. Light the fryer in accordance with the procedure described in Chapter 3, Section 3.2 of the Pro H55-Series Gas Fryer Installation and Operation Manual (P/N 819-5991). 7. After the burners have been lit for at least 90 seconds, observe the flames through the burner sight glasses located on each side of the combustion air blower. Left Viewing Port is behind motor. The air/gas mixture is properly adjusted when the burner manifold pressure is in accordance with the applicable table on page 1-6 and the burners display a bright red-orange glow. If a blue flame is observed or if there are dark spots on the burner face, the air/gas mixture requires adjustment. Adjusting the Air/Gas Mixture On the side of the blower housing opposite the motor is a shutter plate with a locking nut. Loosen the nut enough to allow the shutter to be moved, then adjust the position of the shutter to open or close the air intake opening until a bright red-orange glow is obtained. Carefully hold the shutter in position and tighten the locking nut. 1-12 Loosen this nut and rotate shutter to open or close air intake. Right Viewing Port.
Page 1 and 2: Pro H50/55-Series Gas Fryers Servic
Page 3 and 4: DANGER No structural material on th
Page 5 and 6: PRO H50/55-SERIES GAS FRYERS TABLE
Page 7 and 8: valve via a normally closed high-li
Page 9 and 10: FREQUENTLY USED TEST POINTS FOR INT
Page 11 and 12: 4. On non-CE fryers only, place the
Page 13 and 14: 1.6.2 Replacing the Temperature Pro
Page 15: 1.6.5 Replacing an Ignitor Assembly
Page 19 and 20: ALL OTHER VALVES 4. Carefully unscr
Page 21 and 22: 3. Position a container beneath the
Page 23 and 24: 20. Remove the drain valve(s), temp
Page 25 and 26: To re-assemble with new insulation
Page 27 and 28: 6 5 4 24 23 1 21 7 2 22 8 1-22 1 16
Page 29 and 30: valve handle appears to be in the c
Page 31 and 32: If these causes are ruled out, the
Page 33 and 34: • Shortening that remained in the
Page 35 and 36: the frypot until the rod loses cont
Page 37 and 38: The following processes will assist
Page 39 and 40: Heat Relay (K2 Replaceable) 2 (PWR)
Page 41 and 42: 1. If resistance is not 5 mega-Ohms
Page 43 and 44: 1.9.2 Wiring Diagram for Full-Vat S
Page 45 and 46: 1.10 Principal Wiring Connections F
Page 47 and 48: 1.11.2 Pro H50/55-Series Fryer, Sin
Page 49 and 50: 1.11.4 Pro H50/55-Series Fryer, Sin
Page 51 and 52: 1.11.6 Transformer/Filter Boxes 1.1
Page 53 and 54: 1.11.6.4 FPPH 350/355 Transformer/F
Page 55 and 56: 1.11.8 Modular Basket Lift (208/250
Page 57 and 58: 2.1 Accessories 6 8 PRO H50/55-SERI
Page 59 and 60: ITEM PART # COMPONENT 1 200-2942 Mo
Page 61 and 62: ITEM PART # COMPONENT 1 Back, Singl
Page 63 and 64: ITEM PART # COMPONENT 1 Frame, Cont
Page 65 and 66: ITEM PART # COMPONENT 1 Frame, Cont
Page 67 and 68:
2.5 Drain, Filtration, and Oil Retu
Page 69 and 70:
2.5.2 Drain Valves and Associated C
Page 71 and 72:
2.5.3 Oil Return Line Components Th
Page 73 and 74:
2.5.4 Oil Return Handle, Oil Dispos
Page 75 and 76:
2.5.5 Oil Disposal Wand Assembly 1
Page 77 and 78:
ITEM PART # COMPONENT 1 Valve Assem
Page 79 and 80:
2.6 Electronics and Electrical Comp
Page 81 and 82:
2.6.2 Transformer Boxes 15 10 34 20
Page 83 and 84:
2.6.3 High-Limit Thermostat and Tem
Page 85 and 86:
ITEM PART # COMPONENT 1 106-1019SP
Page 87 and 88:
ITEM PART # COMPONENT 1 106-1018SP
Page 89 and 90:
ITEM PART # COMPONENT 1 Ignitor (in
Page 91 and 92:
ITEM PART # COMPONENT 1 Valve, Non-
Page 93 and 94:
Main Wiring Harnesses U.S. and Non-
Page 95 and 96:
PRO H50/55-SERIES GAS FRYERS CHAPTE
Page 97 and 98:
3.3 Single H50/55 Component Boxes 3
Page 99 and 100:
3.5 Single H50/55 Transformer Boxes
show all

Pro H50/55-Series Gas Fryers Service and Parts Manual - Frymaster

Create successful ePaper yourself

Delete template?

Save as template?