354 268-21 - heidenhain

More documents

Recommendations

Info

18 Clearance cycle group ICP longitudinal contour-parallel ICP transverse contour-parallel With ICP cycles, you define the machining parameters within the cycle description and specify the contour to be machined in an ICP macro. Roughing: The cycle machines the area defined by the “start point X, Z” and the “ICP contour N“ parallel to the contour. Finishing: The cycle finishes the contour area defined by “ICP contour N”. Danger of collision! If the setup and tip angles of the tool have not been defined, the tool plunge-cuts into descending contours at the programmed plunging angle. If the setup and tip angles of the tool have been defined, the tool plunge-cuts at the maximum possible angle. In this case, the resulting contour will not be completely finished and may need to be reworked.
ICP cutting longitudinal ICP cutting transverse With ICP cycles, you define the machining parameters within the cycle description and specify the contour to be machined in an ICP macro. Roughing: The cycle machines the area defined by the “start point X, Z” and the “ICP contour N”. Finishing: The cycle finishes the contour area defined by “ICP contour N”. Finishing: The steeper the tool plunges into the material, the greater the feed rate decrease (maximum: 50%). Danger of collision! If the setup and tip angles of the tool have not been defined, the tool plunge-cuts into descending contours at the programmed plunging angle. If the setup and tip angles of the tool have been defined, the tool plunge-cuts at the maximum possible angle. In this case, the resulting contour will not be completely finished and may need to be reworked. Clearance cycle group 19
Page 1 and 2: Pilot MANUALplus 4110 NC-Software 3
Page 3 and 4: The Pilot ... is your concise progr
Page 5 and 6: Setup Entering machine data (“Set
Page 7 and 8: Tool Measurement You can compare th
Page 9 and 10: Teach-in (Cycle mode) In Teach-in m
Page 11 and 12: Cycles You must set the workpiece d
Page 13 and 14: Rapid traverse positioning Approach
Page 15 and 16: Chamfer The cycle produces a chamfe
Page 17: Plunge longitudinal Plunge transver
Page 21 and 22: ICP recessing radial ICP recessing
Page 23 and 24: ICP recess turning radial ICP reces
Page 25 and 26: Undercut U This cycle machines a
Page 27 and 28: Regroove (longitudinal) thread With
Page 29 and 30: Undercut cycles 28 Thread undercut
Page 31 and 32: Deep-drilling (pecking) axial Deep-
Page 33 and 34: Thread milling axial This cycle mil
Page 35 and 36: Milling cycles 34 Figure axial Figu
Page 37 and 38: Milling cycles 36 Face milling Depe
Page 39 and 40: Pattern linear axial The function
Page 41 and 42: Pattern linear radial The function
Page 43 and 44: DIN Cycle You only need to define t
Page 45 and 46: ICP Contour Elements Line entry: Fi
Page 47 and 48: Thread undercut DIN 76 Undercut DIN
Page 49 and 50: Clearance cycle group Page G818 Lon
Page 51 and 52: Chuck part, cylinder/tube G20 G20 d
Page 53 and 54: Linear path G1 The tool moves linea
Page 55 and 56: Speed limitation for spindle G26/ d
Page 57 and 58: Additive correction G149 To activat
Page 59 and 60: Absolute zero point displacement G5
Page 61 and 62: End of cycle G80 G80 concludes the
Page 63 and 64: Longitudinal contour roughing with
Page 65 and 66: Contour-parallel roughing G836 G836
Page 67 and 68: Contour finishing cycle G89 G89 fin
Page 69 and 70:
Axial contour cutting G861 Radial c
Page 71 and 72:
Axial contour finishing cut G863 Ra
Page 73 and 74:
Axial recess-turning cycle G815 Rad
Page 75 and 76:
Simple thread cycle G32 G32 cuts a
Page 77 and 78:
Metric ISO thread G35 With G35, you
Page 79 and 80:
Tapered API thread G352 This cycle
Page 81 and 82:
Undercut contour G25 The function G
Page 83 and 84:
Undercut DIN509 E with cylinder mac
Page 85 and 86:
Undercut Form H G857 G857 machines
Page 87 and 88:
Simple drilling cycle G71 G71 is us
Page 89 and 90:
Thread tapping cycle G36 G36 can be
Page 91 and 92:
Contour starting point/End-face rap
Page 93 and 94:
End-face circular arc cycle G102/G1
Page 95 and 96:
End-face contour milling cycle G793
Page 97 and 98:
Figure definition end-face complete
Page 99 and 100:
Reference diameters G120 G120 deter
Page 101 and 102:
Lateral-surface circular arc cycle
Page 103 and 104:
Lateral-surface contour milling cyc
Page 105 and 106:
Figure definition lateral-surface r
Page 107 and 108:
Circular pattern on end face G745 W
Page 109 and 110:
Tool Management MANUALplus differen
Page 111 and 112:
Neutral tools The tool orientation
Page 113 and 114:
Threading tools Tool parameters X,
Page 115 and 116:
Milling tools Tool parameters X, Z:
Page 117 and 118:
Setting the workpiece datum 1. Mach
Page 119:
Cycle Overview Workpiece blank Page
show all

354 268-21 - heidenhain

Create successful ePaper yourself

Delete template?

Save as template?