354 268-21 - heidenhain

More documents

Recommendations

Info

Rapid traverse positioning This cycle switches on the C axis, and positions the spindle (C axis) and the tool. Information on the cycle parameters: X2, Z2: End point C2: Final angle A subsequent manual milling cycle switches off the C axis. “Rapid traverse positioning“ is is only required in the Manual mode. Groove axial Groove radial This cycle creates a groove on the end face/lateral surface of a workpiece. The groove width equals the cutter diameter. Information on the cycle parameters: C: Spindle angle (C-axis position) – default: current spindle angle Z1/X1: Upper edge of milling – default: Start point Z/X Z2/X2: Lower edge of milling P: Plunging depth – default: total depth in one infeed FZ: Infeed – default: active feed rate Groove axial Milling cycles 33
Milling cycles 34 Figure axial Figure radial Depending on the parameters, the cycle either mills a contour or roughs/ finishes a pocket on the end face/lateral surface. You can define the following contours: Rectangle (Q=4, LB) Square (Q=4, L=B) Circle (Q=0, RE>0, L and B: no entry) Triangle or polygon (Q=3 or Q>4, L>0) Information on the cycle parameters: U: Overlap factor No entry: Contour milling U>0: Pocket milling – (minimum) overlap of the milling paths = U*cutter diameter H: Cutting direction – default: 0 H=0: Up-cut milling H=1: Down-cut milling J: Contour milling: J=0: On the contour J=1: Inside J=2: Outside Pocket milling: J=0: From the inside out J=1: From the outside in O: Milling procedure (only for pocket milling) – default: 0 O=0: Roughing O=1: Finishing Figure axial Figure radial
Page 1 and 2: Pilot MANUALplus 4110 NC-Software 3
Page 3 and 4: The Pilot ... is your concise progr
Page 5 and 6: Setup Entering machine data (“Set
Page 7 and 8: Tool Measurement You can compare th
Page 9 and 10: Teach-in (Cycle mode) In Teach-in m
Page 11 and 12: Cycles You must set the workpiece d
Page 13 and 14: Rapid traverse positioning Approach
Page 15 and 16: Chamfer The cycle produces a chamfe
Page 17 and 18: Plunge longitudinal Plunge transver
Page 19 and 20: ICP cutting longitudinal ICP cuttin
Page 21 and 22: ICP recessing radial ICP recessing
Page 23 and 24: ICP recess turning radial ICP reces
Page 25 and 26: Undercut U This cycle machines a
Page 27 and 28: Regroove (longitudinal) thread With
Page 29 and 30: Undercut cycles 28 Thread undercut
Page 31 and 32: Deep-drilling (pecking) axial Deep-
Page 33: Thread milling axial This cycle mil
Page 37 and 38: Milling cycles 36 Face milling Depe
Page 39 and 40: Pattern linear axial The function
Page 41 and 42: Pattern linear radial The function
Page 43 and 44: DIN Cycle You only need to define t
Page 45 and 46: ICP Contour Elements Line entry: Fi
Page 47 and 48: Thread undercut DIN 76 Undercut DIN
Page 49 and 50: Clearance cycle group Page G818 Lon
Page 51 and 52: Chuck part, cylinder/tube G20 G20 d
Page 53 and 54: Linear path G1 The tool moves linea
Page 55 and 56: Speed limitation for spindle G26/ d
Page 57 and 58: Additive correction G149 To activat
Page 59 and 60: Absolute zero point displacement G5
Page 61 and 62: End of cycle G80 G80 concludes the
Page 63 and 64: Longitudinal contour roughing with
Page 65 and 66: Contour-parallel roughing G836 G836
Page 67 and 68: Contour finishing cycle G89 G89 fin
Page 69 and 70: Axial contour cutting G861 Radial c
Page 71 and 72: Axial contour finishing cut G863 Ra
Page 73 and 74: Axial recess-turning cycle G815 Rad
Page 75 and 76: Simple thread cycle G32 G32 cuts a
Page 77 and 78: Metric ISO thread G35 With G35, you
Page 79 and 80: Tapered API thread G352 This cycle
Page 81 and 82: Undercut contour G25 The function G
Page 83 and 84: Undercut DIN509 E with cylinder mac
Page 85 and 86:
Undercut Form H G857 G857 machines
Page 87 and 88:
Simple drilling cycle G71 G71 is us
Page 89 and 90:
Thread tapping cycle G36 G36 can be
Page 91 and 92:
Contour starting point/End-face rap
Page 93 and 94:
End-face circular arc cycle G102/G1
Page 95 and 96:
End-face contour milling cycle G793
Page 97 and 98:
Figure definition end-face complete
Page 99 and 100:
Reference diameters G120 G120 deter
Page 101 and 102:
Lateral-surface circular arc cycle
Page 103 and 104:
Lateral-surface contour milling cyc
Page 105 and 106:
Figure definition lateral-surface r
Page 107 and 108:
Circular pattern on end face G745 W
Page 109 and 110:
Tool Management MANUALplus differen
Page 111 and 112:
Neutral tools The tool orientation
Page 113 and 114:
Threading tools Tool parameters X,
Page 115 and 116:
Milling tools Tool parameters X, Z:
Page 117 and 118:
Setting the workpiece datum 1. Mach
Page 119:
Cycle Overview Workpiece blank Page
show all

354 268-21 - heidenhain

Create successful ePaper yourself

Delete template?

Save as template?