Aerocomm AC4868.pdf - HEAnet Mirror Service

More documents

Recommendations

Info

COMPLIANCY INFORMATION 12 AGENCY IDENTIFICATION NUMBERS Agency compliancy is a very important requirement for any product development. AeroComm has obtained modular approval for its products so the OEM only has to meet a few requirements to be eligible to use that approval. The corresponding agency identification numbers and approved antennas are listed below. APPROVED ANTENNA LIST The following antennas are approved for use with the AC4868-250 as identified. The OEM is free to choose another vendor’s antenna of like type and equal or lesser gain as a listed antenna and still maintain compliance. AeroComm Part Number Table 12: Agency Identification Numbers Part Number EUR/EN AC4868-250M Approved Table 13: AC4868-250 Approved Antennas Manufacturer Part Number Manufacturer Type OEM EQUIPMENT LABELING REQUIREMENTS WARNING: The OEM must ensure that the appropriate labeling requirements are met. Following are the requirements for labeling equipment: 1 If the CE marking is reduced or enlarged, the proportions given in the following graduated drawing must be respected. 2 The CE marking must have a height of at least 5 mm except where this is not possible on account of the nature of the apparatus. 3 The CE marking must be affixed to the product or to its data plate. Additionally, it must be affixed to the packaging, if any, and to the accompanying documents. 4 The CE marking must be affixed visibly, legibly, and indelibly. 5 The exclamation point must be included with the CE mark (as shown below) to alert the user to the fact that there are restrictions placed on usage in certain countries. It must have the same height as the CE mark. www.aerocomm.com Gain (dBi) 0600-00020 S467-FL-6-RMM-868S Nearson 1/2 Wave Dipole 2 - X X 2 0 0 A 2 0 0 M 1 0 0 0 M
COUNTRY RESTRICTIONS www.aerocomm.com COMPLIANCY INFORMATION The exclamation point included with the CE mark denotes that the equipment has restrictions in certain countries. Following is a list of countries having restrictions on the AC4868 and a description of those restrictions. The OEM is responsible for ensuring that these restrictions are met. COUNTRY NOTIFICATION Table 14: AC4868 Country Restrictions RF Channel Country Restriction Reason/Remarks 0x38 All countries (unless otherwise noted) Maximum ERP of 500 mW and maximum transmit duty cycle of 10% (amortized over one hour) 0x38 Bulgaria Not implemented 0x38 Finland Audio and voice are not permitted 0x38 Germany Audio and voice are not permitted 0x38 Italy Maximum ERP of 25 mW Military applications 0x38 Slovak Republic Not implemented Military The OEM is responsible for notifying ANY country of the intent to ship product to that country containing the AC4868 four weeks prior to shipping. 31
Page 1 and 2: VERSION 1.2
Page 3 and 4: AC4868-250 TRANSCEIVER MODULE 1 The
Page 5 and 6: PIN DEFINITIONS www.aerocomm.com SP
Page 7 and 8: THEORY OF OPERATION 3 RF ARCHITECTU
Page 9 and 10: SERIAL INTERFACE 4 In order for the
Page 11 and 12: www.aerocomm.com SERIAL INTERFACE s
Page 13 and 14: should be a strong consideration wh
Page 15 and 16: www.aerocomm.com SOFTWARE INTERFACE
Page 17 and 18: Figure 7: Broadcast Mode with Fixed
Page 19 and 20: www.aerocomm.com HARDWARE INTERFACE
Page 21 and 22: AT COMMANDS www.aerocomm.com CONFIG
Page 23 and 24: COMMAND DESCRIPTIONS Enter AT Comma
Page 25 and 26: Write Digital Outputs The OEM Host
Page 27 and 28: EEPROM PARAMETERS 9 The OEM Host ca
Page 29 and 30: Parameter EEPROM Address MAC ID 0x8
Page 31: ORDERING INFORMATION 11 PRODUCT PAR
Page 35 and 36: APPENDIX I - SAMPLE POWER SUPPLY I
Page 37 and 38: www.aerocomm.com APPENDIX I - SAMPL

Aerocomm AC4868.pdf - HEAnet Mirror Service

You also want an ePaper? Increase the reach of your titles

Delete template?

Save as template?