Service Manual - MyLinkDrive

3
OUTLINES AND DIMENSIONS
PKFY-P08NHMU-E2
PKFY-P12NHMU-E2
PKFY-P15NHMU-E2
PKFY-P18NHMU-E2
Sleeve
(purchased locally)
7/16(12.5)
OCH515
2-1/2~3-1/8
(65~80)
A
1-11/16(43)
D
Through hole
2-1/2~3-1/8
(65~80)
Knockout hole for piping
2-3/16(56)
Left side
Knockout hole
for left piping
C
1-3/4(46)
2-3/16(56)
3/16(6)
77-3/16(5.1)
Tapping
screw hole
0
5/8(16)
1-1/16(28.5)
1-9/16(41)
3-1/16(78.5)
3-9/16(91)
4-1/16(103.5)
4-9/16(116)
6-1/2(166)
7(178.5)
8(203.5)
9-1/8(232.5)
9-15/16(253.5)
1-11/16(43)
Wall hole for
left rear piping
2-11/16(69)
7-3/4(197)
Knockout hole
for lower piping
11-9/16(295)
5/16(8)
2-3/16(56)
3/16(6)
2-1/8
(55)
4-5/16(9) Bolt hole
14-5/8(372.3)
14(356.3)
12-7/8(327.5)
11-7/16(291.5)
10-3/8(265)
8-13/16(225)
7-13/16(200)
17-5/8(449)
1-3/4(46)
2-5/16(60)
C
15-1/2(394)
Vane(auto)
10-15/16(278.3)
9-5/16(238)
8-3/8(213)
6-13/16(174)
D
1-11/16(43)
1-11/16(43)
15-3/16(387) 7-1/2(192)
Louver(manual)
2-5/16(59)
B
Front side(Grille open)
4-7/8(125)
27-1/16(688)
17-15/16(457)Gas pipe
21-3/16(539)Liquid pipe
7
2-3/4(70)
23-9/16(599)
35-5/16(898)
0
9/16(15)
0
9/16(15)
0
2-1/4(58)
Knockout hole for
rear piping
2-3/4×12-3/16(70×310)
2-3/4(70)
5/32(3.8)
4-7/8(125)
Center measurement hole 3/32(2.5)
Mount board
4-1/2(115)
5-1/2(140)
6-9/16(167)
7-1/16(180.3)
7-9/16(193.5)
7-13/16(200)
8-13/16(225)
9-5/16(238)
10-3/8(265)
11-7/16(291.5)
12-7/8(237.5)
14(356.3)
14-5/8(372.3)
11-1/16(281)
6-5/8(169)
6-3/16(158)
24(610)Drain hose 7-3/16(184)
Under side
24-1/16(612)
Min.1/4(7)
Knockout hole
for lower piping
Operation lamp
Required space(Indoor unit)
Min.1-31/32(50)
B
Top side
Front side
6-1/16(155)
Wall hole for
right rear piping
Refrigerart
Piping
Liquid pipe
Gas pipe
Drain hose
Indoor unit outline
17-5/8(449)
Min.8-5/8
(220)
Terminal block for power supply
Terminal block for transmission
Terminal block for
MA-remote controller
Emergency operation switch
(cooling/heating)
DEFROST/STAND BY lamp
Receiver
13/16(21.8)
0
3/4(20)
1-1/4(32.7)
2-1/16(53.5)
2-9/16(66)
5(128.5)
6(153.5)
9-1/16(231.5)
10-3/4(273.2)
Knockout hole
for right piping
Air inlet
Air inlet
Right side
Min.5-7/8(150)
Mount board
9-3/4(249)
Air outlet
Unit : inch (mm)
A
1/4F (6.35)
1/2F (12.7)
5/8 (16) I.D
3/16(5)
Min.1-31/32(50)
Min.9-13/16(250)