Release notes Sc1x3 @CHIP-RTOS V1.10 ... - Beck IPC Gmbh

More documents

Recommendations

Info

Category: Serial ports 2 and 3 Synopsis: Memory corruption after exit of program. Description: When a program works with one of the serial ports 2 or 3 and exits, the memory gets corrupted. Fix: Fixed CR Number: 1320 Type: Defect Component: Fossil API Category: RS485 Synopsis: RS485 on serial port 2 and 3. Description: The default hardware mode for TXENABLE pin does not work on serial ports 2 and 3. Fix: Fixed Type: Defect, Component: HW API (4 item(s)) CR Number: 1280 Type: Defect Component: HW API Category: DMA Interrupts Synopsis: The hardware API DMA interrupts do not work. Description: It's not possible to install and use the DMA interrupts. Fix: Fixed CR Number: 1317 Type: Defect Component: HW API Category: PIOs Synopsis: When switching a PIO between the various states, there can be a short period in which the pin is in an unwanted "Normal" or "Output state". Description: Calling the shell commands "PIO 17 4" followed by "PIO 17 2" on SC1x3 leads to a reboot. During the state transition between "Output" and "Input" the PIO is in his "Normal" state for a short time. Because the "Normal" function of PIO17 is HOLD, this leads to a watchdog reset. Fix: Fixed CR Number: 1333 Type: Defect Component: HW API Category: Service Install Interrupt 0x84 Synopsis: Critical section violated by semaphore signalling Description: Run external ETH1 driver task for an hour and this receiver thread may hangs. Fix: Fixed CR Number: 1348 Type: Defect Component: HW API Category: Watchdog 14 von 30
Synopsis: The watchdog is sometimes triggered by the RTOS, although the watchdog mode is set to USER mode. Description: If watchdog mode is set to USER mode, the RTOS still triggers the watchdog inside some code areas, e.g.. the flash write function or when a serial port uses RS485 mode. Fix: Fixed. Do this additional watchdog triggering only when the watchdog mode is set to RTOS mode. Type: Defect, Component: I2C API (2 item(s)) CR Number: 1284 Type: Defect Component: I2C API Category: Software I2C Synopsis: The software I2C mode does not work. Description: The software I2C emulation is not working. Fix: Fixed. CR Number: 1323 Type: Defect Component: I2C API Category: Set I2C speed Synopsis: It's not possible to set the I2C speed. Description: Function that sets I2C speed is not working. Fix: Fixed Type: Defect, Component: SPI API (1 item(s)) CR Number: 1302 Type: Defect Component: SPI API Category: SPI Slave Mode Synopsis: RX and TX pins are swapped in SPI slave mode. Description: This does not match the documentation. Fix: Fixed, swapped RX and TX lines to match the documentation. Type: Defect, Component: TCPIP API (2 item(s)) CR Number: 1316 Type: Defect Component: TCPIP API Category: Set interface MTU Synopsis: User device handle is taken from wrong registers Description: The C-Lib SetIfaceMTU() function passes the userIfaceHandle parameter in registers ES:DI which matches the @Chip-RTOS HTML documentation for this API. However, the SWI function was using registers DX:SI. Fix: Fixed 15 von 30
Page 1 and 2: Release notes SC1x3 @CHIP-RTOS This
Page 3 and 4: Total: 10 Component: CRYPT LIB Cate
Page 5 and 6: Component: RTOS Category: CPU core
Page 7 and 8: Category: CGI pages Synopsis: Addio
Page 9 and 10: Total: 26 Fix: Implemented Type: Ne
Page 11 and 12: Type: Suggestion, Component: CAN Dr
Page 13: Description: 1) If file ends with a
Page 17 and 18: Component: Webserver Category: Driv
Page 19 and 20: CR Number: 1331 Type: Suggestion Co
Page 21 and 22: Total: 41 Description: It shall be
Page 23 and 24: Description: The DIR command of roo
Page 25 and 26: Description: CGI post method does n
Page 27 and 28: Description: New mimetype image/x-i
Page 29 and 30: Type: New Component: I2C API Catego

Release notes Sc1x3 @CHIP-RTOS V1.10 ... - Beck IPC Gmbh

Create successful ePaper yourself

Delete template?

Save as template?