FIXTURLASER ALIGNMENT SYSTEM USER'S MANUAL

More documents

Recommendations

Info

4. By using the inclinometer display, rotate the TD-units to the 9 o’clock position. Slide open the targets, wait until the TD-values appear, and touch the 9 o’clock icon. 5. Using the inclinometer display, rotate the shafts to the 3 o’clock position and touch the 3 o’clock icon. The screen now displays the current horizontal position of the machine. 29
30 6. Rotate the shafts to the 12 o’clock position and touch the 12 o’clock icon. The screen now displays the current vertical position. Re-measuring of all positions. Show horizontal view. Show vertical view. Open Application Set-up. Save the measurement. See Memory Manager. Print a screen dump. Exit from the program.
Page 1 and 2: FIXTURLASER ALIGNMENT SYSTEM USER'S
Page 3 and 4: Measuring OL2R ....................
Page 5 and 6: Mounting Instruction...............
Page 7 and 8: Procedure .........................
Page 10 and 11: INTRODUCTION Congratulations to you
Page 12 and 13: Roll Parallelism Receiver Display R
Page 14 and 15: SAFETY AND CARE POWER SUPPLY Fixtur
Page 17 and 18: TREATMENT AND CARE The Fixturlaser
Page 19 and 20: CALIBRATING THE TOUCH SCREEN To get
Page 21 and 22: . Main Menu - example 20 Battery in
Page 23 and 24: MOUNTING Attach the V-block fixture
Page 25 and 26: PRE-ALIGNMENT FUNCTIONS In the effo
Page 27 and 28: 26 Screen filter From 0 to 10, wher
Page 29: 28 2. Stand by the machine to be ad
Page 33 and 34: Alignment (Clock method) Adjust the
Page 35 and 36: Adjust the lasers to the centre of
Page 37 and 38: If the shafts are rotated to a posi
Page 39 and 40: Rotate the shafts back to the 12 or
Page 42 and 43: SHAFT ALIGNMENT WITH OL2R INTRODUCT
Page 44 and 45: Tolerance table Displays a table wi
Page 46 and 47: the centre of the target on the TD-
Page 48 and 49: Hot condition Using the spirit leve
Page 50 and 51: Cold condition Using the spirit lev
Page 52 and 53: SHAFT ALIGNMENT WITH OL2R When both
Page 54 and 55: SHAFT ALIGNMENT VERTICAL MACHINES I
Page 56 and 57: MEASUREMENT PROCEDURE Settings uniq
Page 58 and 59: Turn the shafts 180° to the 3 o’
Page 60 and 61: ALIGNMENT Adjust the angular error
Page 62 and 63: SHAFT ALIGNMENT CARDAN SHAFTS INTRO
Page 64 and 65: APPLICATION SET-UP Settings unique
Page 66 and 67: COARSE ADJUSTMENT Mount the TD-M un
Page 68 and 69: MEASUREMENT PROCEDURE The screen sh
Page 70 and 71: Using the spirit level in the carda
Page 72: DOCUMENTATION There are three possi
Page 75 and 76: 74 Touch the coupling icon correspo
Page 77 and 78: 76 Confirmation Confirms made selec
Page 79 and 80: ALIGNMENT After you have decided wh
Page 81:
COARSE ADJUSTMENT 80 Distance Selec
Page 84 and 85:
2. Move the Detector to the second
Page 86:
DOCUMENTATION There are three possi
Page 89 and 90:
88 Straightness with Multipoint. Th
Page 91 and 92:
Mounting of the laser transmitter T
Page 93 and 94:
APPLICATION SET-UP Settings unique
Page 95 and 96:
94 Confirmation Confirms made selec
Page 97 and 98:
Repeatability test Before starting
Page 99 and 100:
Measurement screen Measurement scre
Page 101 and 102:
100 To delete all references, touch
Page 103 and 104:
List of measurement points I List s
Page 105 and 106:
The detailed screen shows a curve o
Page 107 and 108:
STRAIGHTNESS WITH ROTATIONAL CENTER
Page 109 and 110:
Measurement point registration Usin
Page 111 and 112:
STRAIGHTNESS WITH CENTER OF BORE AS
Page 113 and 114:
2. Rotate the receiver 180 o (in le
Page 115 and 116:
Measurement point registration Usin
Page 117 and 118:
5. When the Multipoint measurement
Page 119 and 120:
Mounting of the laser transmitter T
Page 121 and 122:
Zeroing of centerpoint Using the me
Page 123 and 124:
Measurement point registration with
Page 125 and 126:
STRAIGHTNESS WITH ARC ANGLE For com
Page 127 and 128:
the micrometer screws on the laser
Page 129 and 130:
Register the values at the 1st posi
Page 131 and 132:
4. Confirm the Arc Angle measuremen
Page 134 and 135:
FLATNESS MEASUREMENT INTRODUCTION I
Page 136 and 137:
Mounting of the receiver R210 The R
Page 138 and 139:
Sampling time Sets the time (in sec
Page 140 and 141:
CONFIGURATION In the Flatness Measu
Page 142 and 143:
COARSE ADJUSTMENT - WHEN USING 3 RE
Page 144 and 145:
MEASUREMENT POINT REGISTRATION The
Page 146 and 147:
Selecting reference points Referenc
Page 148 and 149:
LIST OF MEASUREMENT POINTS List scr
Page 150 and 151:
EVALUATION OF MEASUREMENT RESULT Th
Page 152:
DOCUMENTATION There are three possi
Page 155 and 156:
MOUNTING INSTRUCTION Mounting of th
Page 157 and 158:
Mounting of the Datum Mark Pick-Up
Page 159 and 160:
COARSE ADJUSTMENT The first thing y
Page 161 and 162:
START THE PROGRAM Start the program
Page 163 and 164:
162 Confirmation Confirms made sele
Page 165 and 166:
164 Mount the Detector unit on one
Page 167 and 168:
SETTING UP THE ANGULAR PRISM Before
Page 169 and 170:
Fine centering of the Angular Prism
Page 171 and 172:
170 Move the Detector to the second
Page 173 and 174:
SUMMARY SCREEN The Summary Screen i
Page 175 and 176:
ALIGNMENT . 174 Touch the Roll ID o
Page 178 and 179:
RECEIVER DISPLAY INTRODUCTION In th
Page 180 and 181:
RAW DATA The screen displays the ra
Page 182:
RESUME FUNCTION The program is supp
Page 186 and 187:
MEMORY MANAGER GENERAL FUNCTIONS To
Page 188 and 189:
Exit Touch the delete icon and then
Page 190 and 191:
REVIEWING A SHAFT ALIGNMENT MEASURE
Page 192 and 193:
The appearing screen displays all i
Page 194 and 195:
Tip: Print the summary screen first
Page 196 and 197:
Tip: Print the summary screen first
Page 198 and 199:
SYSTEM SET-UP The System Set-up men
Page 200:
Factory settings in geometrical mea
Page 203 and 204:
PROCEDURE 202 Select sampling time.
Page 206 and 207:
SOFTCHECK A soft foot condition nee
Page 208 and 209:
THERMAL OFFSET Most machines develo
Page 210:
If required you can change to the h
Page 213 and 214:
Switch to horizontal/vertical view
Page 216 and 217:
EXPORT FUNCTION With the Export fun
Page 218:
FIXTURLASER® DU30 DISPLAY UNIT PAR
Page 221 and 222:
Paper feed When the printer is on,
Page 223 and 224:
4 CTS Reserved 5 TXD Data transmiss
Page 225 and 226:
TRANSMITTER/DETECTOR TD-S 10 PART N
Page 227 and 228:
TRANSMITTER/DETECTOR TD-S 100 PART
Page 230:
FIXTURLASER T111 LASER TRANSMITTER
Page 233 and 234:
232
Page 235 and 236:
The value at 9 should be the same (
Page 237 and 238:
Dimensions 175 x 175 x 115 mm Weigh
Page 239 and 240:
CALIBRATION OF THE SPIRIT LEVELS Po
Page 242:
FIXTURLASER R210 RECEIVER PART NO:
Page 246 and 247:
FIXTURLASER AP200 ANGULAR PRISM PAR
Page 248 and 249:
FIXTURLASER FD15 POSITIONING DETECT
Page 250 and 251:
DELTA FIXTURE TM SYSTEM DESCRIPTION
Page 252 and 253:
CENTRELINE MEASUREMENT Definition o
Page 254 and 255:
Measuring Read more in the Advanced
Page 256 and 257:
Mounting on journal. Follow the pro
Page 258 and 259:
OFFSET MEASUREMENT TO ROTATION LINE
Page 260 and 261:
WARNING LABELS TD-M unit, rear TD-S
Page 262:
T220, underneath T220, around prism
Page 266 and 267:
265
show all

FIXTURLASER ALIGNMENT SYSTEM USER'S MANUAL

You also want an ePaper? Increase the reach of your titles

Delete template?

Save as template?