Body Builders Info FUSO HD EURO V FPFVFSNZ PART 10.4 10.10 ...

More documents

Recommendations

Info

10 Technical data 10.9.2 Engine driven power take-off • The engines are fitted with an optional, one or two gear-driven power take-off (PTO). • Both propeller shaft connections and flanged connections (SAE A, SAE B) with toothed sleeves for the corresponding hydraulic pumps are available for the PTO. • The specifications in the "Propeller shafts" section must be taken into consideration for PTO via propeller shafts. • When attaching hydraulic pumps, greasing the tooting off the adapter with lubricating paste (Optimol White T, DBL 6880.10, DC No. A 000 989 80 51) is vital. • All engines are supplied without hydraulic pumps. These must be installed by the vehicle manufacturer. • The hydraulic pipes for the pumps must compensate relative movements between the engine and vehicle (body), be vibration-resistant and be located sufficiently far away from hot parts; a shield to the hot exhaust gas leading components may be necessary. • All PTO leading from the engine must be calculated or checked by MITSUBISHI FUSO in terms of technical, torsional vibrations. • Retrofitting a PTO involves a great deal of effort, because the engine has to be dismantled to do this. Output Torques The engine scope of delivery must contain the codes specified for the maximum possible output torques listed in the following. OM 457 • Maximum rated torque 600 Nm on continuous operation • Maximum peak torque 720 Nm for short-term operation (e.g. starting and shifting) • To prevent the maximum permissible torque from being exceeded, suitable overload protection must be fitted (e.g. pressure limitation, blocking protection, overload clutch). i 10.9 Power take-offs MITSUBISHI FUSO body/equipment mounting directives for FP.FV.FS Issue date: 16. 01. 2013 ! Only print out complete sections from the current version 344
10 Technical data PTO Layout Variant 1 Rigid attachment Variant 2 With propeller shaft Variant 3 With propeller shaft and elastic clutch 1 Engine 2 Power take-off 3 Driven unit 4 Propeller shaft 5 Elastic clutch, drawing : A 444 250 00 01 i 10.9 Power take-offs A Mass moment of inertia of driven major unit B Mass moment of inertia of driven major unit plus propeller shaft C Mass moment of inertia of propeller shaft plus propeller shaft-side part of the elastic clutch Consider permissible block bending moment (max. 60 Nm), from rear edge flywheel housing D1 Mass moment of inertia of propeller shaft-side part of the elastic clutch D2 Mass moment of inertia aggregate-lateral part of the elastic clutch E Mass moment of inertia of flange plus driven aggregate plus aggregate lateral part of the flexible clutch MITSUBISHI FUSO body/equipment mounting directives for FP.FV.FS Issue date: 16. 01. 2013 ! Only print out complete sections from the current version 345
Page 1 and 2:
Body/equipment mounting directives
Page 3 and 4:
Contents 1 Introduction 1.1 The aim
Page 5 and 6:
1 Introduction MITSUBISHI FUSO TRUC
Page 7 and 8:
1 Introduction a Risk of accident B
Page 9 and 10:
1 Introduction 1.3 Vehicle safety a
Page 11 and 12:
1 Introduction 1.5 Accident prevent
Page 13 and 14:
2 General 2.1 Vehicle and model des
Page 15 and 16:
FUSO Model LOCAL Model GCW FP54SGR3
Page 17 and 18:
10 Technical data i 10.4 Weight di
Page 19 and 20:
10 Technical data Model FV54SJR5VFA
Page 21 and 22:
E 10 Technical data Model FS52SS3FA
Page 23 and 24:
A E E 10 Technical data 10.5 Chassi
Page 25 and 26:
10 Technical data FV51SK3VFAA FV51S
Page 27 and 28:
10 Technical data FV54ST3VFAA i 10.
Page 29 and 30:
10 Technical data FV54SJR5VFAB i 10
Page 31 and 32:
10 Technical data FS52SS3VFAA FS52S
Page 33 and 34:
E 10 Technical data FS52SS3FAA i 10
Page 35 and 36: 10 Technical data FP54SGR3VFAA i 10
Page 37 and 38: A 10 Technical data FV51SK2FAA i 10
Page 39 and 40: E 10 Technical data FV54STK3VFAA i
Page 41 and 42: 10 Technical data FV54SJR5VFAA i 10
Page 43 and 44: 10 Technical data FS52SS5VFAB i 10.
Page 45 and 46: 10 Technical data 10.5.3 Reference
Page 47 and 48: 10 Technical data FS52SSVF (OM457+G
Page 49 and 50: 10 Technical data i 10.5 Chassis ca
Page 51 and 52: 10 Technical data 10.6 Frame struct
Page 53 and 54: 10 Technical data i 10.6 Frame stru
Page 63 and 64: 10 Technical data i 10.6 Frame str
Page 71 and 72: A E E 10 Technical data 10.6.3 Posi
Page 73 and 74: A 10 Technical data 10.6 Frame stru
Page 75 and 76: 10 Technical data i E 10.6 Frame s
Page 77 and 78: 10 Technical data Rear air suspensi
Page 79 and 80: 10 Technical data Second front axle
Page 81 and 82: E A 10 Technical data NOTE; Basic
Page 83 and 84: A E A 10 Technical data 10.9 Power
Page 85: E 10 Technical data G230-12 Model i
Page 89 and 90: 10 Technical data i Detailed view o
Page 91 and 92: 10 Technical data 40-liter tank (Fr
Page 93 and 94: Index E Electric circuit continuity
Page 95 and 96: Index R Rear hooks . . . . . . . .
Page 97: Revision record E D C B A 16. Jan.
show all

Body Builders Info FUSO HD EURO V FPFVFSNZ PART 10.4 10.10 ...

You also want an ePaper? Increase the reach of your titles

Delete template?

Save as template?