Bluetooth Commands - wless.ru

More documents

Recommendations

Info

Chapter 2 – AT Commands 17 GET SNIFF SETTINGS Set Using: ATSSNIFF Return Parameters: ,,, (HEX) EXAMPLE: TYPE: REPLY: ATSI,17 OK Not Set! OR OK 0000,0000,0000,0000 18 GET LINK SUPERVISORY TIMEOUT Set Using: ATLSTO Return Parameters: (HEX) EXAMPLE: TYPE: REPLY: ATSI,18 OK 04 19 GET LIST OF PAIRED OR SECURED ADDRESSES Set Using: ATPAIR Return Parameters: Index, (HEX) EXAMPLE: TYPE: REPLY: ATSI,19 OK 00, 01, 02, 03, Note: 00 – 03 are for indexing the stored addresses only. They do not indicate that the address is associated with any specific channel. 20 GET CHANNEL UUIDS Set Using: ATSSNC Return Parameters: ,,, (UUIDs for Ch01-03 will only be returned if enabled using ATSSW3) EXAMPLE: TYPE: REPLY: ATSI,20 OK 1101 //Point to point OR 1101,1101,1101 //Multipoint with 3 channels 21 GET SPECIFIC TRANSMISSION CHANNEL Set Using: ATSWC Return Parameters: , EXAMPLE: TYPE: REPLY: ATSI,21 OK 01,03 22 GET FTP/OPP CONNECTION STATUS Return Parameters: Connection Status: 0 = Disconnected, 1 = Connected EXAMPLE: TYPE: REPLY: ATSI,22 OK 1 Multi-Tech Systems, Inc. SocketWireless Bluetooth AT Commands (S000360G) 20
Chapter 2 – AT Commands Security Commands SSW,2 Set Security Level Sets the Security Level register state. Format: ATSSW,2, Parameters: Security Modes: 0 = Link Level – Highest level of security. 1 = Service Level – Provides service information without using PIN. Factory Default: VM Mode EXAMPLE: TYPE: ATSSW,2,1 REPLY: OK OR ERROR Read Using: ATRSW,2 RSW,2 Get Security Level Gets the Security Level register state. Format: ATRSW,2 Return Parameters: EXAMPLE: TYPE: ATRSW,2 REPLY: OK OR 00 Set Using: ATSSW,2 Max Number of Bluetooth Connections Commands SSW, 3 Set Max Connection Number Sets the maximum number of Bluetooth connections. Enables multi-point mode if number of connections is greater than one. Format: ATSSW,3, Parameters: Number of Connections: Integer Value 1-4 Factory Default: 1 EXAMPLE: TYPE: ATSSW,3,1 REPLY: OK Notes: • Fast Data Mode is supported with only 1 connection and the ##,00 packet header is never sent. It is recommended you limit the number of connections for your application to maximize performance and security. • Requires a reset for change to take affect. • By default data is broadcast to all connected radios when the local radio is in data mode. The radio can be set to transmit to a specific channel using the ATSWC command. (See the Utilities section for more information) RSW, 3 Read Max Connection Number Reads the maximum number of Bluetooth connections. Format: ATRSW,3 Return Parameters: EXAMPLE: TYPE: TRSW,3 REPLY: OK 01 Multi-Tech Systems, Inc. SocketWireless Bluetooth AT Commands (S000360G) 21
Page 1 and 2: Bluetooth ® Commands AT Commands a
Page 3 and 4: Table of Contents Table of Contents
Page 5 and 6: Table of Contents RSSI and Link Qua
Page 7 and 8: Chapter 1 - Introduction Overview C
Page 9 and 10: Chapter 1 - Introduction Important
Page 11 and 12: Chapter 1 - Introduction Multipoint
Page 13 and 14: Chapter 1 - Introduction Test Scena
Page 15 and 16: Chapter 2 - AT Commands Chapter 2 -
Page 17 and 18: Chapter 2 - AT Commands Set/Get Dev
Page 19: Chapter 2 - AT Commands 11 GET PIO(
Page 23 and 24: Chapter 2 - AT Commands SSNC Set Se
Page 25 and 26: Chapter 2 - AT Commands OP Overwrit
Page 27 and 28: Chapter 2 - AT Commands SW21 Write
Page 29 and 30: Chapter 2 - AT Commands SW23 Write
Page 31 and 32: Chapter 2 - AT Commands SW26 Lock U
Page 33 and 34: Chapter 2 - AT Commands Read Memory
Page 35 and 36: Chapter 2 - AT Commands Notes: •
Page 37 and 38: Chapter 2 - AT Commands Set Master
Page 39 and 40: Chapter 2 - AT Commands About Comma
Page 41 and 42: Chapter 2 - AT Commands Pairing Com
Page 43 and 44: Chapter 2 - AT Commands SSNIFF Enab
Page 45 and 46: Chapter 2 - AT Commands Notes: •
Page 47 and 48: Chapter 2 - AT Commands Link Superv
Page 49 and 50: Chapter 2 - AT Commands Making the
Page 51 and 52: Chapter 2 - AT Commands • If the
Page 53 and 54: Chapter 2 - AT Commands FTP Push/Pu
Page 55 and 56: Chapter 2 - AT Commands OPP Client
Page 57 and 58: Chapter 2 - AT Commands OPPPUSH Obj
Page 59 and 60: Chapter 2 - AT Commands OPP Server
Page 61 and 62: Chapter 4 - Examples Chapter 4 - Ex
Page 63 and 64: Chapter 4 - Examples DUN Point-to-P
Page 65 and 66: Chapter 4 - Examples - Perform a Ma
Page 67 and 68: Chapter 4 - Examples - At second ma
Page 69 and 70: Chapter 4 - Examples Issue these AT
Page 71 and 72:
Appendix A - AT Command Summary Tab
Page 73 and 74:
Appendix A - AT Command Summary Tab
Page 75 and 76:
Appendix B - Responses AT Example L
Page 77 and 78:
AT Example Long Response Example Sh
Page 79 and 80:
Appendix B - Responses AT Example L
Page 81 and 82:
Appendix C - UUID Table Appendix C
Page 83 and 84:
Appendix E - Two Versions of Blueto
Page 85 and 86:
Appendix E - Two Versions of Blueto
Page 87 and 88:
Appendix F - Glossary, Acronyms, an
Page 89 and 90:
IL - Last Inquiry..................
show all

Bluetooth Commands - wless.ru

You also want an ePaper? Increase the reach of your titles

Delete template?

Save as template?