instructions home cinema dvd/cd control center rx-dv3rsl - JVC

Basic DVD Player Operations
For details about DVD player operations, see pages 33 to
46.
• You can also play back MP3 and JPEG files. See pages 47
to 50.
• When using remote control, press DVD to change the
remote control operation mode to the DVD player
operation.
1 Open the Disc Tray
Before turning on the unit, turn on your TV and select the correct
video input (see the manual supplied with your TV).
• When you use a JVC’s TV, you can turn on your TV by pressing
STANDBY/ON TV on the remote control and select the
video input by pressing TV/VIDEO. (If your TV is not a JVC’s,
see “Operating Other Manufacturers’ Equipment” on page 63.)
• For changing the OSD messages—the information on the TV
—into the desired language, see pages 51 and 53.
On the front panel ONLY
Press 0.
The unit is turned on and the disc tray opens.
The STANDBY lamp goes off and the illumination lamp lights up.
• When a disc is already loaded, pressing 3 turns on the unit and
starts playing back the loaded disc.
2 Load a Disc
Place a disc correctly with its label side up.
DVD
VCR
TAPE/CDR
SOURCE NAME
RX-DV3 HOME CINEMA DVD/CD CONTROL CENTER
STB
TV
CORRECT
By pressing the following buttons, you can pause, advance, or reverse
playback, and locate the beginning of the title, chapter, or track.
On the front panel
From the remote control
To stop playback temporarily
Press 8.
• Pressing 3 starts playback again.
REW/( TUNING 9/FF
FM MODE
STROBE
– TV/STB CH +
To move back the playback position by 10 seconds
(for DVD VIDEO only)
Press 3 during DVD VIDEO playback.
The unit moves the playback position about 10 seconds before the
current position, then resumes playback.
To advance or reverse playback rapidly
Press and hold ¢ or 4.
While you are pressing and holding ¢ (or 4), the unit advances
(or reverses: for DVD VIDEO and audio CD) playback 5 times as
fast as the normal speed. When you press and hold ¢ (or 4)
further, the playback speed changes up to 20 times as fast as the
normal speed.
• Releasing the button resumes the normal playback.
To locate the beginning of the chapter or track
Press ¢ or 4.
Press ¢ (or 4) to locate the beginning of the next (current or
previous) chapter or track.
To locate the chapter or track using the number buttons
Press the number buttons (1–10, +10) to select the number of the
desired chapter or track.
EFFECT CENTER
Ex. : To select 3, press 3.
1 2 3
To select 11, press +10, then 1.
TEST REAR·L
To select 20, press +10, then 10.
4 5 6
SURR ON/OFF REAR·R
7 8 9
From the remote control ONLY
SURR MODE – SUBWOOFER +
10/0 +10
100+
STANDBY/ON
STANDBY
INPUT
ANALOG/DIGITAL
INPUT ATT.
ON/OFF
SURROUND
MODE
D I G ITA L
S U R R O U N D
3 Start Playback
TUNING
INCORRECT
About indication on the display while playing back a disc
While you are playing back a disc, the playback information
appears on the display as follows:
Ex. : When DVD VIDEO is loaded
DIGITAL AUTO
AUTO SURROUND
DIGITAL L C R
SUBWFR
LFE
SPK.
VOLUME
LS
RS
On the front panel
From the remote control
Press 3.
The disc tray closes and the unit starts playing back the loaded disc.
• You can also close the disc tray by pressing 0 on the front panel.
Chapter number Elapsed playing time
Ex. : When audio CD is loaded
DIGITAL AUTO PRO LOGIC
L R
SPK.
VOLUME
SUBWFR
Track number
Elapsed playing time
15