CORiTEC Milling Strategies: iCAM V3 - imes-icore GmbH
CORiTEC Milling Strategies: iCAM V3 - imes-icore GmbH
CORiTEC Milling Strategies: iCAM V3 - imes-icore GmbH
Create successful ePaper yourself
Turn your PDF publications into a flip-book with our unique Google optimized e-Paper software.
<strong>CORiTEC</strong> <strong>Milling</strong> <strong>Strategies</strong>: <strong>iCAM</strong> <strong>V3</strong><br />
<strong>Milling</strong> <strong>Strategies</strong><br />
Overview<br />
Rev. 1.0 / 03.06.10 <strong>Milling</strong> <strong>Strategies</strong> (Overview)<strong>Milling</strong><br />
<strong>Strategies</strong> (Overview).docx<br />
Page 1 of 10
<strong>CORiTEC</strong> <strong>Milling</strong> <strong>Strategies</strong>: <strong>iCAM</strong> <strong>V3</strong><br />
Preamble<br />
Each individual tooth-technical restoration represents an unique. So unique it is, so individual<br />
and multilayered are the work procedures, knowledge and talents of each technician which are<br />
necessary for reaching high-quality and aesthetic artificial dentures.<br />
This manual should be a guideline in order to achieve optimal results.<br />
Please take the time and read this manual for working with the <strong>CORiTEC</strong> system before start<br />
working in order to be able to offer your patient the optimum quantity of quality.<br />
© <strong>imes</strong>-<strong>icore</strong> <strong>GmbH</strong><br />
All rights reserved<br />
Despite all care misprint and mistakes cannot be excluded.<br />
For improvement suggestions and referring to errors we are grateful.<br />
Rev. 1.0 / 03.06.10 <strong>Milling</strong> <strong>Strategies</strong> (Overview)<strong>Milling</strong><br />
<strong>Strategies</strong> (Overview).docx<br />
Page 2 of 10
<strong>CORiTEC</strong> <strong>Milling</strong> <strong>Strategies</strong>: <strong>iCAM</strong> <strong>V3</strong><br />
Content<br />
I. Short comments ................................................................................................................... 4<br />
A. Strategy glossary (<strong>iCAM</strong> <strong>V3</strong>): ................................................................................................... 4<br />
B. Strategy options: ..................................................................................................................... 4<br />
C. Tool positions: ......................................................................................................................... 4<br />
II. Overview: milling strategies ................................................................................................. 5<br />
A. ZrO 2 :......................................................................................................................................... 5<br />
B. PMMA: ..................................................................................................................................... 6<br />
C. Wax: ......................................................................................................................................... 7<br />
D. CoCr: ........................................................................................................................................ 8<br />
E. Ti: ............................................................................................................................................. 9<br />
Rev. 1.0 / 03.06.10 <strong>Milling</strong> <strong>Strategies</strong> (Overview)<strong>Milling</strong><br />
<strong>Strategies</strong> (Overview).docx<br />
Page 3 of 10
<strong>CORiTEC</strong> <strong>Milling</strong> <strong>Strategies</strong>: <strong>iCAM</strong> <strong>V3</strong><br />
I. Short Comments<br />
A. Strategy glossary (<strong>iCAM</strong> <strong>V3</strong>):<br />
For different processing a number of different strategies are available. Thereby we differentiate<br />
according to the materials which can be worked on.<br />
For the materials Zirconium Dioxide, PMMA and Wax tools with 3mm and 6mm shafts are<br />
available. These have work diameters of 0.6mm, 1.0mm and 2.5mm.<br />
For Titanium and CoCr alloys 3mm and 6mm shafts are likewise used. Here the working parts of<br />
the tools have a diameter of 1.0mm, 2.0mm and 3.0mm.<br />
For these constellations in each case individual strategies are developed.<br />
These always follow the same sample:<br />
could be such a strategy.<br />
ico - Zr - crown - 0.6 – 3mm<br />
Glossary Comment of sample alternative options<br />
File format: ico (<strong>imes</strong>-<strong>icore</strong> format) also free format for stl- files and infformat<br />
Material: Zr (Zirconium oxide) PMMA, Wax, CoCr, Ti<br />
Object type: crown abutment, bridge, telescope<br />
Diameter: 0.6 (0.6mm milling tool cone point) 1.0, 2.0, 2.5, 3.0<br />
(milling tools outside work)<br />
Shaft diameter: 3mm (3mm shaft milling tools) 6mm<br />
(of the milling tool)<br />
B. Strategy options:<br />
For the different materials there are milling strategies adapted in each case (have a look at<br />
chapter II - overview milling strategies). The tool diameter applies only to the occlusal face of the<br />
objects which can be worked on. The interiors treatment (marginal fit range and cement gap) is<br />
always worked on with the 1mm tool. For the treatment of zirconium you have the additionally<br />
possibility of the small-steps- and safety strategies. These strategies are particularly careful to<br />
the material and leave it usually also to mill very filigrane portions.<br />
C. Tool positions:<br />
material Zr PMMA Wax CoCr Ti<br />
machine 0.6 1.0 2.5 0.6 1.0 2.5 0.6 1.0 2.5 1.0 2.0 3.0 1.0 2.0 3.0<br />
340i 15 14 13 15 12 11 15 12 11<br />
440i 15 14 13 15 12 11 15 12 11<br />
450i 15 14 13 15 12 11 15 12 11<br />
540i 15 14 13 15 12 11 15 12 11 9 7/8 6/10 4 2 1<br />
550i 15 14 13 15 12 11 15 12 11 9 7/8 6/10 4 2 1<br />
750i 15 14 13 15 12 11 15 12 11 9 7/8 6/10 4 2 1<br />
Rev. 1.0 / 03.06.10 <strong>Milling</strong> <strong>Strategies</strong> (Overview)<strong>Milling</strong><br />
<strong>Strategies</strong> (Overview).docx<br />
Page 4 of 10
<strong>CORiTEC</strong> <strong>Milling</strong> <strong>Strategies</strong>: <strong>iCAM</strong> <strong>V3</strong><br />
II.<br />
Overview: <strong>Milling</strong> <strong>Strategies</strong><br />
A. ZrO2:<br />
kind of work<br />
Abutment<br />
Bridge<br />
Crown<br />
Telescope<br />
Inlay<br />
Abutment<br />
Bridge<br />
Crown<br />
Telescope<br />
Inlay<br />
Abutment<br />
Bridge<br />
Crown<br />
Telescope<br />
Inlay<br />
file tool diameter 340i 440i 450i 540i 550i 750i<br />
.ico<br />
.ico<br />
.ico<br />
.ico<br />
.ico<br />
.free<br />
.free<br />
.free<br />
.free<br />
.free<br />
.inf<br />
.inf<br />
.inf<br />
.inf<br />
.inf<br />
0,6mm 1,0mm 2,5mm<br />
2,5<br />
safety<br />
3mm 3mm 6mm 6mm 6mm 6mm<br />
Rev. 1.0 / 03.06.10 <strong>Milling</strong> <strong>Strategies</strong> (Oberview) Page 5 of 10
<strong>CORiTEC</strong> <strong>Milling</strong> <strong>Strategies</strong>: <strong>iCAM</strong> <strong>V3</strong><br />
B. PMMA:<br />
kind of work<br />
Abutment<br />
Bridge<br />
Crown<br />
Telescope<br />
Inlay<br />
Abutment<br />
Bridge<br />
Crown<br />
Telescope<br />
Inlay<br />
Abutment<br />
Bridge<br />
Crown<br />
Telescope<br />
Inlay<br />
file<br />
(Format)<br />
.ico<br />
.ico<br />
.ico<br />
.ico<br />
.ico<br />
.free<br />
.free<br />
.free<br />
.free<br />
.free<br />
.inf<br />
.inf<br />
.inf<br />
.inf<br />
.inf<br />
tool diameter 340i 440i 450i 540i 550i 750i<br />
0,6mm 1,0mm 2,5mm<br />
2,5<br />
safety<br />
3mm 3mm 6mm 6mm 6mm 6mm<br />
Rev. 1.0 / 03.06.10 <strong>Milling</strong> <strong>Strategies</strong> (Oberview) Page 6 of 10
<strong>CORiTEC</strong> <strong>Milling</strong> <strong>Strategies</strong>: <strong>iCAM</strong> <strong>V3</strong><br />
C. Wax:<br />
kind of work<br />
Abutment<br />
Bridge<br />
Crown<br />
Telescope<br />
Inlay<br />
Abutment<br />
Bridge<br />
Crown<br />
Telescope<br />
Inlay<br />
Abutment<br />
Bridge<br />
Crown<br />
Telescope<br />
Inlay<br />
file<br />
(Format)<br />
.ico<br />
.ico<br />
.ico<br />
.ico<br />
.ico<br />
.free<br />
.free<br />
.free<br />
.free<br />
.free<br />
.inf<br />
.inf<br />
.inf<br />
.inf<br />
.inf<br />
tool diameter 340i 440i 450i 540i 550i 750i<br />
0,6mm 1,0mm 2,5mm<br />
2,5<br />
safety<br />
3mm 3mm 6mm 6mm 6mm 6mm<br />
Rev. 1.0 / 03.06.10 <strong>Milling</strong> <strong>Strategies</strong> (Oberview) Page 7 of 10
<strong>CORiTEC</strong> <strong>Milling</strong> <strong>Strategies</strong>: <strong>iCAM</strong> <strong>V3</strong><br />
D. CoCr:<br />
kind of work<br />
Abutment<br />
Bridge<br />
Crown<br />
Telescope<br />
Inlay<br />
Abutment<br />
Bridge<br />
Crown<br />
Telescope<br />
Inlay<br />
Abutment<br />
Bridge<br />
Crown<br />
Telescope<br />
Inlay<br />
file<br />
(Format)<br />
.ico<br />
.ico<br />
.ico<br />
.ico<br />
.ico<br />
.free<br />
.free<br />
.free<br />
.free<br />
.free<br />
.inf<br />
.inf<br />
.inf<br />
.inf<br />
.inf<br />
tool diameter 340i 440i 450i 540i 550i 750i<br />
0,6mm 1,0mm 2,0mm<br />
2,0<br />
safety<br />
3mm 3mm 6mm 6mm 6mm 6mm<br />
Rev. 1.0 / 03.06.10 <strong>Milling</strong> <strong>Strategies</strong> (Oberview) Page 8 of 10
<strong>CORiTEC</strong> <strong>Milling</strong> <strong>Strategies</strong>: <strong>iCAM</strong> <strong>V3</strong><br />
E. Ti:<br />
kind of work<br />
Abutment<br />
Bridge<br />
Crown<br />
Telescope<br />
Inlay<br />
Abutment<br />
Bridge<br />
Crown<br />
Telescope<br />
Inlay<br />
Abutment<br />
Bridge<br />
Crown<br />
Telescope<br />
Inlay<br />
file<br />
(Format)<br />
.ico<br />
.ico<br />
.ico<br />
.ico<br />
.ico<br />
.free<br />
.free<br />
.free<br />
.free<br />
.free<br />
.inf<br />
.inf<br />
.inf<br />
.inf<br />
.inf<br />
tool diameter 340i 440i 450i 540i 550i 750i<br />
0,6mm 1,0mm 2,0mm<br />
2,0<br />
safety<br />
3mm 3mm 6mm 6mm 6mm 6mm<br />
Rev. 1.0 / 03.06.10 <strong>Milling</strong> <strong>Strategies</strong> (Oberview) Page 9 of 10
<strong>imes</strong>-<strong>icore</strong> <strong>GmbH</strong><br />
Im Leibolzgraben 16<br />
36132 Eiterfeld<br />
Fon: +49 (0) 6672 / 898 228<br />
Fax: +49 (0) 6672 / 898 222<br />
www.<strong>imes</strong>-<strong>icore</strong>.de<br />
info@<strong>imes</strong>-<strong>icore</strong>.de<br />
Rev. 1.0 / 03.06.10 <strong>Milling</strong> <strong>Strategies</strong> (Overview).docx Page 10 of 10
Change language