Advantages and Disadvantages of Different Types of Neutral ...

More documents

Recommendations

Info

Per IEEE… TO HRG OR NOT TO HRG? IEEE Std 242-2001 (Buff Book) Recommended Practice for Electric Power Distribution for Industrial Plants 8.2.5 Once the system is high-resistance grounded, overvoltages are reduced; and modern, highly sensitive ground-fault protective equipment can identify the faulted feeder on the first fault and open one or both feeders on the second fault before arcing burn down does serious damage. 68
Design Considerations with HRG Systems National Electrical Code (2005) 250.36 High-impedance grounded neutral systems in which a grounding impedance, usually a resistor, limits the ground-fault current to a low value shall be permitted for 3-phase ac systems of 480 volts to 1000 volts where all the following conditions are met: 1) The conditions of maintenance and supervision ensure that only qualified persons service the installation. 2) Continuity of power is required. 3) Ground detectors are installed on the system. 4) Line-to-neutral loads are not served. 69
Page 1 and 2:
Advantages and Disadvantages of Dif
Page 3 and 4:
POWER SYSTEM GROUNDING Power system
Page 5 and 6:
Are You at Risk? Do you use electri
Page 7 and 8:
POWER SYSTEM GROUNDING SYSTEM FAILU
Page 9 and 10:
Bolted Faults Result from a solid c
Page 11 and 12:
Arc Fault Usually caused by insulat
Page 13:
Arcing Ground Faults Intermittent o
Page 16 and 17:
Industry Recommendations IEEE Std 2
Page 18 and 19: THE UNGROUNDEDED POWER SYSTEM 18
Page 20 and 21: UNGROUNDED SYSTEM NORMAL CONDITIONS
Page 22 and 23: UNGROUNDED SYSTEM GROUND FAULT ON P
Page 24 and 25: THE UNGROUNDED POWER SYSTEM GROUND
Page 26 and 27: THE UNGROUNDED POWER SYSTEM ADVANTA
Page 28 and 29: THE SOLIDLY GROUNDED POWER SYSTEM 2
Page 30 and 31: SOLIDLY GROUNDED SYSTEM THREE PHASE
Page 32 and 33: SOLIDLY GROUNDED SYSTEM LINE - GROU
Page 34 and 35: SOLIDLY GROUNDED SYSTEM LINE-LINE S
Page 36 and 37: Industry Recommendations IEEE Std 1
Page 38 and 39: THE SOLIDLY GROUNDED POWER SYSTEM D
Page 40 and 41: Reactive Grounding Uses reactor not
Page 42 and 43: LOW RESISTANCE GROUNDING OF POWER S
Page 44 and 45: LOW RESISTANCE GROUNDED ZERO SEQUEN
Page 46 and 47: HIGH RESISTANCE GROUNDING OF POWER
Page 48 and 49: No Single Phase Loads No line-to-ne
Page 50 and 51: HIGH RESISTANCE GROUNDING - GROUND
Page 52 and 53: HIGH RESISTANCE GROUNDED SYSTEM LIN
Page 54 and 55: HIGH RESISTANCE GROUNDING 54
Page 56 and 57: THE HIGH RESISTANCE GROUNDED POWER
Page 58 and 59: THE HIGH RESISTANCE GROUNDED POWER
Page 60 and 61: HOW DO YOU FIND GROUND FAULTS? Ungr
Page 62 and 63: PROCEDURE FOR LOCATING GROUND FAULT
Page 64 and 65: Fault Location Method to quickly lo
Page 66 and 67: Per IEEE… TO HRG OR NOT TO HRG? I
Page 70 and 71: Duty Ratings for NGR’s IEEE Std 3
Page 72 and 73: HIGH RESISTANCE GROUNDING OF A 2400
Page 74 and 75: THE HIGH RESISTANCE GROUNDING OF PO
Page 76 and 77: Resolve NEC requirement Add small 1
Page 78 and 79: Minimum Specifications 120 Volt Con
Page 80 and 81: HIGH RESISTANCE GROUNDING - 2.4KV S
Page 82 and 83: HIGH RESISTANCE GROUNDING 2.4KV SYS
Page 84 and 85: HIGH RESISTANCE GROUNDING - 2.4KV S
Page 86: GENERATOR APPLICATONS OF NEUTRAL GR
Page 89 and 90: Generator Grounding - IEEE IEEE Std
Page 91 and 92: AIC Rating (Amps Interrupting Curre
Page 93 and 94: HYBRID SYSTEM 93
Page 95: Common options Enclosure rating Enc
Page 101 and 102: 101
Page 103 and 104: 103
show all

Advantages and Disadvantages of Different Types of Neutral ...

Create successful ePaper yourself

Delete template?

Save as template?