Intelliflo VF Installation / Owners Manual - Pool Center

More documents

Recommendations

Info

22 Time and Contrast Menu Use the “Time and Contr” menu settings to set the IntelliFlo system clock and to adjust the control panel display contrast. The IntelliFlo system clock controls all scheduled start and stop times, functions, and programmed cycles. The system clock can store the correct time for up to 96 hours after power is shut off. After 96 hours the clock must be reset to the correct time. Setting System Time To set the IntelliFlo system clock: 1. Ensure that the green power LED is on and the pump is stopped. 2. Press the Menu button. “Pool Data” is displayed. 3. Press the Up or Down arrows and select “Time/Contr.” 4. Press the Select button to access “Time/Contr” setting. 5. Press the Select button to change the current minutes and hour. Warn. 6. To change the minute and hour digits, press the Left and Right Alarm arrow buttons to select which digit to modify, then use the Up Feature Feature Start 1 2 Stop and Down arrow buttons to change the selected digit. Note, that the hours selection is from 01 to 11 for A.M. and P.M. The system time is displayed on the main screen, A.M. and P.M. are not displayed. 7. Press the Enter button to save the setting. Setting the LCD Backlight Contrast IntelliFlo ® MENU 12:24 Time/Contr On Filter Select Vacuum Enter Back Wash Escape Manual Menu Reset Filter On Warn. Alarm Feature 1 IntelliFlo ® Time/Contr 12:24 12:29 am Set Time Select Vacuum Feature 2 Enter Back Wash Start Stop Escape Manual Menu Reset To change the contrast of the control panel display : 1. Ensure that the green power LED is on and the pump is stopped. 2. Press the Menu button. “Pool Data” is displayed. 3. Press the Up or Down arrows and select “Time/Contr.” 4. Press the Select button. 5. Press the Up or Down arrows and select “Contrast Level.” 6. Press the Select button. The contrast levels are 0 to 9. Avoid using 0 unless screen is unreadable in bright sun 7. Press the Enter button to save the setting. Filter On Warn. Alarm Feature 1 IntelliFlo ® Time/Contr 12:36 Select 5 Contrast Level Vacuum Feature 2 Enter Back Wash Start Stop Escape Manual Menu Reset Filter On Warn. Alarm Feature 1 IntelliFlo ® Time/Contr 12:38 Select 7 Contrast Level Vacuum Feature 2 Enter Back Wash Start Stop Escape Manual Menu Reset IntelliFlo VF Installation and User’s Guide
23 Features Mode The Feature mode can be used with water features such as spa, cleaner, waterfalls, etc. You can schedule start and stop times for each feature. All Features are operated using Flow control. The Feature mode and Filter mode are run simultaneously. The three types of features are; Features 1 & 2, Features 3 -9 and M.O. Flo: Features 1 and 2 Feature 1 and Feature 2 run for a pre-defined duration with a specifically set flow. If Feature 1 or Feature 2 buttons are pressed, all other Features are temporarily deactivated. Feature 1 or Feature 2 cannot be used in Backwash Mode. Features 1 and 2 have a higher priority than the pre-programmed Features 3-9. After the preset duration time for the Feature 1(2), IntelliFlo will switch back to the “Filter” mode if the IntelliFlo was in “Filter” mode when the Feature 1 (2) button had been pressed. After the preset duration time for the Feature 1(2), the IntelliFlo will switch back to the “Manual” mode if IntelliFlo was in “Manual” mode when the Feature 1 (2) button had been pressed. Features 3 -9 Features 3 through 9 are only active in Filter mode. These features run a set flow for a specified time. The Features 3-9 can not overlap. M. O. Flo The M. O. Flo feature automatically increases the pump flow to allow the system heater to check the water temperature and switch on if necessary. This feature is only active when the pump is running a filter cycle. Once the heater checks for heat and discovers it must fire it will send a signal back to IntelliFlo to go into “Heater” mode. M.O. Flo only works during the “Filter” mode selected time cycles IntelliFlo VF Installation and User’s Guide
Page 1 and 2: IntelliFlo ® VF Variable Flow Pump
Page 3 and 4: i Contents Important Safety Precaut
Page 5 and 6: F iii IMPORTANT SAFETY PRECAUTIONS
Page 7 and 8: v IMPORTANT SAFETY PRECAUTIONS (con
Page 9 and 10: IntelliFlo ® VF Overview 1 Section
Page 11 and 12: 3 Operator control panel cover Driv
Page 13 and 14: This section describes the operator
Page 15 and 16: 7 Navigating the Menu Structure Bef
Page 17 and 18: This section describes how to use t
Page 19 and 20: 11 Manual Mode (Continued) 9. Press
Page 21 and 22: 13 Pool Data Mode Use the Pool Data
Page 23 and 24: 15 Priming Mode (Continued) 6. To s
Page 25 and 26: 17 Filter Mode (Continued) 5. To se
Page 27 and 28: 19 Filter Mode (Continued) Clean Fi
Page 29: 21 Filter Mode (Continued) Flow Con
Page 33 and 34: 25 Features Mode (Continued) The fu
Page 35 and 36: 27 3. To enable Feature 3: Press th
Page 37 and 38: 29 External Control with IntelliCom
Page 39 and 40: 31 Controlling IntelliFlo with the
Page 41 and 42: 33 Backwash Mode When the Filter mo
Page 43 and 44: 35 Vacuum Mode Use Vacuum mode to c
Page 45 and 46: 37 Section 4 User Maintenance The f
Page 47 and 48: 39 Winterizing The IntelliFlo’s i
Page 49 and 50: Section 5 Installation and Removal
Page 51 and 52: 43 Pump Disassembly WARNING — Alw
Page 53 and 54: 45 Drive Assembly Removal and Insta
Page 55 and 56: 12.50 47 IntelliFlo VF Pump Dimensi
Page 57 and 58: Alerts and Warnings The IntelliFlo
Page 59 and 60: 51 IntelliFlo VF Installation and U
Page 61 and 62: 53 How to make your pool more energ
Page 63 and 64: 55 Notes IntelliFlo VF Installation
Page 65 and 66: Notes

Intelliflo VF Installation / Owners Manual - Pool Center

You also want an ePaper? Increase the reach of your titles

Delete template?

Save as template?