Ball and Roller Bearings - Ntn-snr.com

Tapered Roller Bearings
Inch system sizes
J system series
r1
T
C
D
B
r
d
a
d 28.57531.750mm
Boundary dimensions Basic load ratings Limiting speeds
dynamic static dynamic static
mm kN kgf rpm
d D T B C C r C or C r C or grease oil
28.575
29.000
29.367
29.987
30.000
30.112
30.162
30.213
30.226
58.738 19.050 19.355 15.080 40.5 44.5 4,150 4,550 6,700 8,900
60.325 19.842 17.462 15.875 39.5 45.5 4,050 4,650 6,700 8,900
60.325 19.845 19.355 15.875 40.5 44.5 4,150 4,550 6,700 8,900
62.000 19.050 20.638 14.288 46.5 54.0 4,750 5,500 6,100 8,200
64.292 21.433 21.433 16.670 51.5 64.5 5,250 6,600 6,100 8,100
66.421 23.812 25.433 19.050 64.5 72.5 6,550 7,400 6,200 8,200
68.262 22.225 22.225 17.462 57.0 67.0 5,800 6,850 5,800 7,700
68.262 22.225 23.812 17.462 57.5 65.5 5,850 6,700 5,700 7,700
69.850 23.812 25.357 19.050 69.0 81.5 7,050 8,300 5,700 7,600
72.626 24.608 24.257 17.462 58.0 55.5 5,900 5,700 5,800 7,700
73.025 22.225 22.225 17.462 56.5 68.0 5,750 6,900 5,300 7,000
50.292 14.224 14.732 10.668 28.0 35.5 2,860 3,600 7,200 9,600
66.421 23.812 25.433 19.050 64.5 72.5 6,550 7,400 6,200 8,200
62.000 16.002 16.566 14.288 39.0 42.0 3,950 4,300 6,300 8,400
62.000 19.050 20.638 14.288 46.5 54.0 4,750 5,500 6,100 8,200
69.012 19.845 19.583 15.875 48.5 58.0 4,900 5,900 5,600 7,400
72.000 29.370 27.783 23.020 72.0 97.0 7,350 9,850 5,400 7,100
62.000 19.050 20.638 14.288 46.5 54.0 4,750 5,500 6,100 8,200
62.000 16.002 16.566 14.288 39.0 42.0 3,950 4,300 6,300 8,400
64.292 21.433 21.433 16.670 51.5 64.5 5,250 6,600 6,100 8,100
69.850 23.812 25.357 19.050 69.0 81.5 7,050 8,300 5,700 7,600
72.626 30.162 29.997 23.812 84.5 98.0 8,600 9,950 5,500 7,300
62.000 19.050 20.638 14.288 46.5 54.0 4,750 5,500 6,100 8,200
62.000 19.050 20.638 14.288 46.5 54.0 4,750 5,500 6,100 8,200
62.000 19.050 20.638 14.288 46.5 54.0 4,750 5,500 6,100 8,200
69.012 19.845 19.583 15.875 48.5 58.0 4,900 5,900 5,600 7,400
69.012 19.845 19.583 15.875 48.5 58.0 4,900 5,900 5,600 7,400
59.131 15.875 16.764 11.811 34.5 41.0 3,500 4,150 6,300 8,400
62.000 18.161 19.050 14.288 46.5 54.0 4,750 5,500 6,100 8,200
62.000 19.050 20.638 14.288 46.5 54.0 4,750 5,500 6,100 8,200
Note: 1. With regard to the chamfer dimensions on the back face of the inner and outer rings, installation dimensions ras and r1as are larger than the maximum value.
2. For the inner bore diameter of bearings with bearing numbers marked "†" (inner ring), this value applies only to high precision class types, Class 4 and 2.
B-160
31.750