TC35i Module TC35i Terminal

More documents

Recommendations

Info

TC35i AT Command Set Confidential / Released 2.18 ATQ Set result code presentation mode Write command ATQ[] Response Specifies whether or not the TA transmits any result code to the TE. Information text transmitted in response is not affected by this setting. If =0: OK If =1: (none) Parameter 0 DCE transmits result code 1 Result codes are suppressed and not transmitted Reference V.25ter Note 2.19 ATP Select pulse dialing Execute command ATP Response OK Reference V.25ter Note No effect for GSM 2.20 ATS0 Set number of rings before automatically answering the call Read command ATS0? Write command ATS0= Response OK Specifies whether or not the TA will accept an incoming call without user intervention. determines the number of rings to wait before the TA will automatically answer. Response OK Parameter 000 disables automatic answer mode 001-255 enables automatic answering after specified number of rings Reference V.25ter Note If is set too high, the calling party may hang up before the call can be automatically answered. The correlation between ATS7 and ATS0 is important. Example: Call setup may fail if ATS0=20 and ATS7=30. The selected value is local to the interface. It is possible to set different values on different interfaces (channels). In such cases the interface ‘wins’ which is idle and uses the smallest ATS0 value. Autoanswer mode can be set on each multiplexer channel. On Channels 2 and 3 it applies only to voice calls. TC35i_ATC_V01.05 Page 32 of 278 04.08.2003
TC35i AT Command Set Confidential / Released 2.21 ATS3 Write command line termination character Read command ATS3? Write command ATS3= Reference V.25ter Response OK This parameter setting determines the character recognized by TA to terminate an incoming command line. Response OK Parameter 000-013-127 command line termination character Note Using other value than 13 can cause problems when entering commands. 2.22 ATS4 Set response formatting character Read command ATS4? Write command ATS4= Reference V.25ter Response OK This parameter setting determines the character generated by the TA for result code and information text. Response OK Parameter 000-010-127 response formatting character. Note 2.23 ATS5 Write command line editing character Read command ATS5? Write command ATS5= Reference V.25ter Response OK This parameter setting determines the character recognized by TA as a request to delete the immediately preceding character from the command line. Response OK Parameter 000-008-127 command line editing character Note 2.24 ATS6 Set pause before blind dialing Read command ATS6? Write command ATS6= Reference V.25ter Response OK No effect for GSM Response OK Parameter Note 000-255 number of seconds to wait before blind dialing. TC35i_ATC_V01.05 Page 33 of 278 04.08.2003
Page 1 and 2: Siemens Cellular Engines TC35i Modu
Page 3 and 4: TC35i AT Command Set Confidential /
Page 31: TC35i AT Command Set Confidential /
Page 83 and 84:
TC35i AT Command Set Confidential /
Page 85 and 86:
Page 87 and 88:
Page 89 and 90:
Page 91 and 92:
Page 93 and 94:
Page 95 and 96:
Page 97 and 98:
Page 99 and 100:
Page 101 and 102:
Page 103 and 104:
Page 105 and 106:
Page 107 and 108:
Page 109 and 110:
Page 111 and 112:
Page 113 and 114:
Page 115 and 116:
Page 117 and 118:
Page 119 and 120:
Page 121 and 122:
Page 123 and 124:
Page 125 and 126:
Page 127 and 128:
Page 129 and 130:
Page 131 and 132:
Page 133 and 134:
Page 135 and 136:
Page 137 and 138:
Page 139 and 140:
Page 141 and 142:
Page 143 and 144:
Page 145 and 146:
Page 147 and 148:
Page 149 and 150:
Page 151 and 152:
Page 153 and 154:
Page 155 and 156:
Page 157 and 158:
Page 159 and 160:
Page 161 and 162:
Page 163 and 164:
Page 165 and 166:
Page 167 and 168:
Page 169 and 170:
Page 171 and 172:
Page 173 and 174:
Page 175 and 176:
Page 177 and 178:
Page 179 and 180:
Page 181 and 182:
Page 183 and 184:
Page 185 and 186:
Page 187 and 188:
Page 189 and 190:
Page 191 and 192:
Page 193 and 194:
Page 195 and 196:
Page 197 and 198:
Page 199 and 200:
Page 201 and 202:
Page 203 and 204:
Page 205 and 206:
Page 207 and 208:
Page 209 and 210:
Page 211 and 212:
Page 213 and 214:
Page 215 and 216:
Page 217 and 218:
Page 219 and 220:
Page 221 and 222:
Page 223 and 224:
Page 225 and 226:
Page 227 and 228:
Page 229 and 230:
Page 231 and 232:
Page 233 and 234:
Page 235 and 236:
Page 237 and 238:
Page 239 and 240:
Page 241 and 242:
Page 243 and 244:
Page 245 and 246:
Page 247 and 248:
Page 249 and 250:
Page 251 and 252:
Page 253 and 254:
Page 255 and 256:
Page 257 and 258:
Page 259 and 260:
Page 261 and 262:
Page 263 and 264:
Page 265 and 266:
Page 267 and 268:
Page 269 and 270:
Page 271 and 272:
Page 273 and 274:
Page 275 and 276:
Page 277 and 278:
show all

TC35i Module TC35i Terminal

You also want an ePaper? Increase the reach of your titles

Delete template?

Save as template?