NuDAM® - Q Products

More documents

Recommendations

Info

Default Setting • RS-485 Interface DIP Switch Setting RS-485 (Default) RS-422 RS-232 34 • NuDAM-6530
4.3 Installation Software Utility ND-6530 Driver. Equipments for Installation A computer with USB port Window 98 or Win2000 operation system USB host controller installed on the system USB cable (type A to type B) Windows 98 Installation: 1. Plug the ND-6530 into the computer USB port or a USB hub. The New Hardware Wizard appears, click on Next to continue.(show as figure) NuDAM-6530 • 35
Page 1 and 2: NuDAM ® ND-6520 RS-232 to RS-422/R
Page 3 and 4: Table of Contents Chapter 1 Introdu
Page 5 and 6: 1 Introduction 1.1 What is NuDAM ?
Page 7 and 8: A surface coating covers on the PCB
Page 9 and 10: 1.6 NuDAM RS-485 Network Configurat
Page 11 and 12: Host ND-6510 Repeater ND-6520: RS-2
Page 13 and 14: 1.9. Shielding In case of increased
Page 15 and 16: 2 NuDAM-6520 2.1. Overview What is
Page 17 and 18: A Look at NuDAM-6520 & Pin Assignme
Page 19 and 20: Functional Block Diagram Power Inpu
Page 21 and 22: SW1 Setting SW 1 D efault Setting (
Page 23 and 24: 2.4 Programming The NuDAM-6520 is a
Page 25 and 26: Input / Output ♦ Interface : RS-4
Page 27 and 28: Pin Definitions Pin # Signal Name D
Page 29 and 30: SW1 Setting SW1 Default Setting (96
Page 31 and 32: Application Wiring NuDAM module NuD
Page 33 and 34: • Up to 128 RS-485 devices on the
Page 35 and 36: A Look at NuDAM-6510 & Pin Assignme
Page 37: 4.2 Setup Objective of Setup In nor
Page 41 and 42: 4. In the dialog box that comes up,
Page 43 and 44: Windows 2000 Installation 1. Plug t
Page 45 and 46: 5. Then you should use the driver t
Page 47 and 48: Application Wiring RS-485 For RS-48
Page 49 and 50: 4.4 Programming The NuDAM-6530 is a
Page 51 and 52: Specifications of NuDAM-6521 Trans
Page 53 and 54: Pin Definitions Pin # Signal Name D
Page 55 and 56: 5.2 Initialation & Installation Sof
Page 57 and 58: Initialization Wiring 5.3. Install
Page 59 and 60: (Leading Code) (Addr) (Command Vari
Page 61 and 62: Read Command Leading Code ~(Addr)0
Page 63 and 64: @Example User command: Response: %0
Page 65 and 66: @Description Read module‘s name.
Page 67 and 68: 5.4.7 Soft Reset @Description Reset
Page 69 and 70: 5.4.9 Set RTS Status @Description S
Page 71 and 72: 5.4.11 Read CTS Status @Description
Page 73 and 74: 5.4.13 Read Device ID @Description
Page 75 and 76: 5.4.15 Read Delimiter @Description
Page 77 and 78: 5.4.17 Open/Close Data Gate @Descri
Page 79 and 80: @Example User command: ~300 Respons
Page 81 and 82: 5.4.20 Set Host Watchdog Timer @Des
Page 83 and 84: 5.4.22 Host is OK @Description When
Page 85 and 86: 6.3 NuDAM Administration Function O
Page 87 and 88: 6.3.3 Using Operations Operation-Te
Page 89 and 90:
Operation-Run Batch : Run batch com
Page 91 and 92:
6.3.4 Save and Print Nudam modules
Page 93 and 94:
Troubleshooting and Maintenance Pre
Page 95:
• Damage caused by inappropriate
show all

NuDAM® - Q Products

You also want an ePaper? Increase the reach of your titles

Delete template?

Save as template?