NuDAM® - Q Products

More documents

Recommendations

Info

2. In the dialog box that comes up, leave the default choice (Search for the best drivers for your device), click on Next to continue. 3. In the dialog box that comes up, leave the default choice (Floppy disk drives), insert the distribution diskette in the floppy (A:) drive, click on Next to continue. 36 • NuDAM-6530
4. In the dialog box that comes up, click on Next to continue. Files are now copied to your hard disk. 5. After the driver files have been copied to the hard disk, a dialog box appears to tell you that the installation has finished. Click on Finish.(show as figures) NuDAM-6530 • 37
Page 1 and 2: NuDAM ® ND-6520 RS-232 to RS-422/R
Page 3 and 4: Table of Contents Chapter 1 Introdu
Page 5 and 6: 1 Introduction 1.1 What is NuDAM ?
Page 7 and 8: A surface coating covers on the PCB
Page 9 and 10: 1.6 NuDAM RS-485 Network Configurat
Page 11 and 12: Host ND-6510 Repeater ND-6520: RS-2
Page 13 and 14: 1.9. Shielding In case of increased
Page 15 and 16: 2 NuDAM-6520 2.1. Overview What is
Page 17 and 18: A Look at NuDAM-6520 & Pin Assignme
Page 19 and 20: Functional Block Diagram Power Inpu
Page 21 and 22: SW1 Setting SW 1 D efault Setting (
Page 23 and 24: 2.4 Programming The NuDAM-6520 is a
Page 25 and 26: Input / Output ♦ Interface : RS-4
Page 27 and 28: Pin Definitions Pin # Signal Name D
Page 29 and 30: SW1 Setting SW1 Default Setting (96
Page 31 and 32: Application Wiring NuDAM module NuD
Page 33 and 34: • Up to 128 RS-485 devices on the
Page 35 and 36: A Look at NuDAM-6510 & Pin Assignme
Page 37 and 38: 4.2 Setup Objective of Setup In nor
Page 39: 4.3 Installation Software Utility N
Page 43 and 44: Windows 2000 Installation 1. Plug t
Page 45 and 46: 5. Then you should use the driver t
Page 47 and 48: Application Wiring RS-485 For RS-48
Page 49 and 50: 4.4 Programming The NuDAM-6530 is a
Page 51 and 52: Specifications of NuDAM-6521 Trans
Page 53 and 54: Pin Definitions Pin # Signal Name D
Page 55 and 56: 5.2 Initialation & Installation Sof
Page 57 and 58: Initialization Wiring 5.3. Install
Page 59 and 60: (Leading Code) (Addr) (Command Vari
Page 61 and 62: Read Command Leading Code ~(Addr)0
Page 63 and 64: @Example User command: Response: %0
Page 65 and 66: @Description Read module‘s name.
Page 67 and 68: 5.4.7 Soft Reset @Description Reset
Page 69 and 70: 5.4.9 Set RTS Status @Description S
Page 71 and 72: 5.4.11 Read CTS Status @Description
Page 73 and 74: 5.4.13 Read Device ID @Description
Page 75 and 76: 5.4.15 Read Delimiter @Description
Page 77 and 78: 5.4.17 Open/Close Data Gate @Descri
Page 79 and 80: @Example User command: ~300 Respons
Page 81 and 82: 5.4.20 Set Host Watchdog Timer @Des
Page 83 and 84: 5.4.22 Host is OK @Description When
Page 85 and 86: 6.3 NuDAM Administration Function O
Page 87 and 88: 6.3.3 Using Operations Operation-Te
Page 89 and 90: Operation-Run Batch : Run batch com
Page 91 and 92:
6.3.4 Save and Print Nudam modules
Page 93 and 94:
Troubleshooting and Maintenance Pre
Page 95:
• Damage caused by inappropriate
show all

NuDAM® - Q Products

You also want an ePaper? Increase the reach of your titles

Delete template?

Save as template?