EmCORE-i6315

More documents

Recommendations

Info

Integrated Peripherals CMOS SETUP UTILITY - Copyright (C) 1984-2001 Award Software Integrated Peripherals OnChip IDE Channel0 [Enabled] OnChip IDE Channel1 [Enabled] IDE Prefetch Mode [Enabled] Primary Master PIO [Auto] Primary Slave PIO [Auto] Secondary Master PIO [Auto] Secondary Slave PIO [Auto] Primary Master UDMA [Auto] Primary Slave UDMA [Auto] Secondary Master UDMA [Auto] Secondary Slave UDMA [Auto] Init Display First [PCI Slot] IDE HDD Block Mode [Enabled] Onboard FDD Controller [Enabled] Onboard Serial Port 1 [Auto] Onboard Serial Port 2 [Auto] UART 2 Mode [Standard] IR Function Duplex Half Tx, Rx inverting enable No, Yes Onboard Parallel Port [378/IRQ7] Onboard Parallel Mode [Normal] ECP Mode Use DMA 3 Parallel Port EPP Type EPP1.9 Onboard Serial Port 3 [3E8] Serial Port 3 Use IRQ [IRQ11] Onboard Serial Port 4 [2E8] Serial Port 4 Use IRQ [IRQ10] Onboard Parallel Port 2 [378] Parallel Port 2 Use IRQ [IRQ5] Parallel Port 2 Mode [Normal] LPT2 ECP Mode Use DMA 3 Onboard Legacy Audio [Enabled] Sound Blaster [Disabled] SB I/O Base Address [220H] SB IRQ Select [IRQ 5] SB DMA Select [DMA1] MPU-401 [Disabled] MPU-401 I/O Address [330-333H] GAME Port (200-207H) [Enabled] Item Help Menu Level Allows you to choose the VIRUS warning feature for IDE Hard Disk boot sector protection. If this function is enabled and someone attempt to write data into this area, BIOS will show a warning message on screen and alarm beep ¯ ® ¬:Move Enter:Select +/-/PU/PD:Value F10:Save ESC:Exit F1:General Help F5:Previous Values F6:Fail-SAfe Defaults F7:Optimized Defaults 52 EmCORE-i6315 User's Manual
OnChip IDE Channel 0/1 Select "Enabled" to activate each on-board IDE channel separately, Select "Disabled", if you install an add-on IDE Control card IDE Prefetch Mode Enable prefetching for IDE drive interfaces that support its faster drive accesses. If you are getting disk drive errors, change the setting to omit the drive interface where the errors occur. Depending on the configuration of your IDE subsystem, this field may not appear, and it does appear when the Internal PCI/IDE filed, above, is Disabled. Primary & Secondary Master/Slave PIO These four PIO fields let you set a PIO mode (0-4) for each of four IDE devices. When under "Auto" mode, the system automatically set the best mode for each device Primary & Secondary Master/Slave UDMA When set to "Auto" mode, the system will detect if the hard drive supports Ultra DMA mode. Init Display First Select "AGP" or "PCI Slot" for system to detect first when boot-up. IDE HDD Block Mode This feature enhances disk performance by allowing multi-sector data transfers and eliminates the interrupt handling time for each sector. Onboard FDD Controller Select "Enabled" to activate the on-board FDD Select "Disabled" to activate an add-on FDD Onboard Serial Port 1 & 2 Select an address and corresponding interrupt for the first/second serial port. The default value for the first serial port is "3F8/IRQ4" and the second serial port is "2F8/IRQ3". UART 2 Mode Select to activate the Infrared transfer function. Onboard Parallel Port Select address and interrupt for the Parallel port. Onboard Parallel Mode Select an operating mode for the parallel port. Mode options are Normal, EPP, ECP, ECP/EPP. ECP Mode Use DMA Select a DMA channel if parallel Mode is set as ECP, ECP/EPP. Parallel Port EPP Type Select a EPP Type if parallel Port is set as EPP, ECP/EPP. EmCORE-i6315 User's Manual 53
Page 1 and 2:
EmCORE-i6315 5¼" Pentium III Minib
Page 3 and 4:
Table of Contents Specifications ..
Page 5 and 6: Specifications General Specificatio
Page 7 and 8: Warning Single Board Computers and
Page 9 and 10: Dimensions 136.0 5.0 23.4 114.9 58.
Page 11 and 12: Jumper/Connector Quick Reference Ju
Page 13 and 14: 6 ON 1 2 3 4 Watchdog Timer The onb
Page 15 and 16: 6 ON 1 2 3 4 DiskOnChip ® 2000 Fla
Page 17 and 18: 6 ON 1 2 3 4 Serial Port (COM2) Mod
Page 19 and 20: 6 ON 1 2 3 4 Chassis Auxilary Fan C
Page 21 and 22: Interface Connectors HDD, FDD Flopp
Page 23 and 24: Enhanced IDE Connector (IDE2) 44-pi
Page 25 and 26: Onboard RS-232 Serial Port (JCOM) 2
Page 27 and 28: Keyboard (JKB&MS) Connector : JKB&M
Page 29 and 30: System Resources Interrupt Assignme
Page 31 and 32: This page intetionally left blank E
Page 33 and 34: 6 ON 1 2 3 4 Flat Panel Connector P
Page 35 and 36: KYOCERA KCB104VG2BA-A01 Display typ
Page 37 and 38: HITACHI LMG9211XUCC Display type :
Page 39 and 40: TORISAN MXS121022010 Display type :
Page 41 and 42: This page intetionally left blank E
Page 43 and 44: Setup Items The main menu includes
Page 45 and 46: Floppy Mode 3 Support Enables suppo
Page 47 and 48: Cylinder Min = 0 Max = 65535 Set th
Page 49 and 50: CPU Internal Cache/External Cache T
Page 51 and 52: Chipset Features Setup CMOS SETUP U
Page 53 and 54: However, if your RAM modules cannot
Page 55: PCI # 2 Access # 1 Retry This BIOS
Page 59 and 60: ACPI Suspend Type S1 (POS) Power On
Page 61 and 62: PnP/PCI Configuration CMOS SETUP UT
Page 63 and 64: POST Codes The following codes are
Page 65 and 66: 14 Test Timer Test 8254 Timer 0 Cou
Page 67 and 68: 4F Security Check Ask password secu
Page 69 and 70: What if things go wrong if you use
show all

EmCORE-i6315

You also want an ePaper? Increase the reach of your titles

Delete template?

Save as template?