Operations Manual - PRO-101FD - Pioneer Electronics

More documents

Recommendations

Info

02 Install Your Flat Panel Display 2.2.1 Check the Location for Suitability When choosing the location for your panel, there are several factors to keep in mind. The installation site should be out of direct sunlight and have sufficient ventilation around the flat panel display to allow cooling. The diagram below is an example of a stand-mounted panel with proper ventilation. Over 50 cm (19 11/16 inches) Over 10 cm (3 15/16 inches) The distance behind and above the panel changes depending on your choice of mount. Consult with your dealer or professional installer for proper ventilation. Use the checklist below to judge possible installation sites. Sufficient ventilation Safe from excessive vibrations Away from air conditioners Free of moisture or dampness No danger of splashing water Route cords and cables safely No danger of power overloads Separate from other IR equipment Protected from hits or shocks Distance from heat sources Out of direct sunlight Away from strong lighting sources For specific cautions and safety information, refer to “8.2 Physical Location & Temperature Considerations” and “8.8 Safety Precautions.” 2.2.2 Lift and/or Move Your Panel (the How To’s) This flat panel display is built for endurance but because of the technology, the panel must be handled with care. Use the handles attached to the rear of the flat panel display to lift the unit. To avoid flexing or twisting the unit, you need at least two people to lift and move the panel. Do not move the flat panel display by holding only a single handle or by dragging the panel by its handles. (PRO-141FD) (PRO-101FD) 14 En Note: Do not use the handles to hang the flat panel display or as anchors to prevent the panel from slipping or tipping after it is mounted.
Install Your Flat Panel Display 02 2.2.3 Mount the Flat Panel Display Because your flat panel display is slim but heavy, have at least two people mount and/or position the panel. The following sections provide instructions for the different mounting and anchoring options. Anchor the Panel When Using a Stand When using a stand, stabilize the panel to keep it from tipping over. Please use the metal fittings and screws supplied with the optional stand to anchor the panel to a wall or other solid support structure. Another option is to purchase hooks, cords, and fittings through your installer or from your local hardware store. The hardware size and strength depends on the composition and thickness of the anchoring surface. Recommended hook: Nominal diameter 8 mm (3/8 inch), length 12 mm to 18 mm (0.5 inches to 0.7 inches) To anchor the panel when using the optional stand, follow the steps below. 1 ) Attach the hooks to the mounting holes on the back of the panel. 2 ) Sink the fittings into the wall or support structure. 3 ) Run cords between the hooks and the fittings. 1.Hook 4 ) Tighten the cords until the panel is anchored but 2.Cord not pulled off balance. Fitting M8 12 mm to 18 mm (0.5 inches to 0.7 inches) (PRO-141FD) To stabilize the flat panel display on a table or platform, use the metal fittings and screws supplied with the optional stand as well as commercially available wood screws. The wood screws are to anchor the metal fittings when mounting on a wooden surface. These screws should have a nominal diameter of 4 mm (5/32 inch) and are at least 20 mm (13/16 inch) long. Notes: Avoid moving the table after the panel is attached. Do not use bare wires for the cord. If any part of the wire is introduced into the ventilation port on the back of the display panel, fire or electrical shock could result. 15 En
Page 2 and 3: IMPORTANT The lightning flash with
Page 4 and 5: TABLE OF CONTENTS 4 En 5.1 Choose a
Page 6 and 7: 01 Introduction to the Flat Panel D
Page 12 and 13: 02 Install Your Flat Panel Display
Page 22 and 23: 03 Basic Operations 3.2 Program You
Page 24 and 25: 03 Basic Operations 3.2.4 Assign a
Page 26 and 27: 04 Basic Picture Adjustment For sta
Page 28 and 29: 04 Basic Picture Adjustment 4.2 Sma
Page 30 and 31: 04 Basic Picture Adjustment 4.2.7 T
Page 32 and 33: 05 Additional Picture Adjustment Op
Page 46 and 47: 06 Use Other Equipment With Your Fl
Page 64 and 65:
06 Use Other Equipment With Your Fl
Page 66 and 67:
Page 68 and 69:
Page 70 and 71:
Page 72 and 73:
Page 74 and 75:
Page 76 and 77:
07 Helpful Information Why does the
Page 78 and 79:
07 Helpful Information Picture Issu
Page 80 and 81:
08 Cautions and Warnings 80 En 8 Ca
Page 82 and 83:
08 Cautions and Warnings In rare ca
Page 84 and 85:
08 Cautions and Warnings 8.9.2 Radi
Page 86 and 87:
09 Appendix 9.1.2 Satellite Brand/C
Page 88 and 89:
09 Appendix 9.1.3 VCR Brand/Code Br
Page 90 and 91:
09 Appendix Brand/Code Brand/Code B
Page 92 and 93:
09 Appendix 9.1.5 DVD-R Brand/Code
Page 94 and 95:
09 Appendix Brand/Code Brand/Code B
Page 96 and 97:
09 Appendix 9.2 Video/PC Signals (H
Page 98 and 99:
09 Appendix 9.2.4 INPUT 3 (D-Sub) -
Page 100 and 101:
09 Appendix Resolution Dot-Line Hf
Page 102 and 103:
09 Appendix 9.4 Trademarks Trademar
Page 104 and 105:
09 Appendix DHCP The Dynamic Host C
Page 106:
Register Your Product on http://www
show all

Operations Manual - PRO-101FD - Pioneer Electronics

Create successful ePaper yourself

Delete template?

Save as template?