Operations Manual - PRO-101FD - Pioneer Electronics

More documents

Recommendations

Info

01 Introduction to the Flat Panel Displays 1.2.2 Operating the Remote Control The remote control for the flat panel display is a powerful tool. This section provides a brief introduction to your remote control while later sections explore more advanced operations. Insert the Batteries into the Remote Control To open, push and slide the battery cover in the direction of the arrows. Load the supplied two AA size batteries by the negative polarity (–) ends first. The batteries supplied with this product may have a shorter life expectancy due to storage conditions. If the remote control seems to be failing or is weak, replace the provided batteries with new alkaline batteries. Never mix old and new batteries. Mixing old and new batteries can shorten the life of new batteries or cause chemical leaks in old batteries. Also, mixing different types or brands of batteries can cause issues as batteries brands have slightly different characteristics. Note: If the flat panel display’s remote control is not needed for an extended length of time, remove the batteries. When disposing of used batteries, please comply with governmental regulations or environmental public institution’s rules that apply in your country/area. 8 En
Introduction to the Flat Panel Displays 01 Remote Control Issues There are a small number of issues that can affect your remote control but the most common is weak batteries. Weak batteries in the remote control can cause communication to fail or only operate sporadically. In this situation, try moving closer to the panel and attempt to control the panel with the remote. If the panel responds, change the batteries. If moving closer has no effect on the panel, check the surroundings for objects that might be blocking the signal. Also consider other equipment with remote controls that are in the area around the panel. Objects and other IR signals can disrupt the remote. For more help with your remote control, refer to “7.1 Frequently Asked Questions (FAQs)”. Operating Range for the Remote Control To control the flat panel display, point the remote towards the sensor on the panel’s bottom right corner. For easy operation, keep the distance between the remote control and the sensor less than 7 m (23 feet) and at an angle of less than 30 degrees. 30º 7 m (23 feet) 30º Sensor The remote control may not work properly if the sensor is in direct sunlight or very bright lighting. If your viewing room is naturally bright, change the position of the panel or physically use the remote control closer to the panel’s sensor. Note: If the remote control is left sitting in direct sunlight or under a very strong light, the case could warp or deform. 9 En
Page 2 and 3: IMPORTANT The lightning flash with
Page 4 and 5: TABLE OF CONTENTS 4 En 5.1 Choose a
Page 6 and 7: 01 Introduction to the Flat Panel D
Page 10 and 11: 01 Introduction to the Flat Panel D
Page 12 and 13: 02 Install Your Flat Panel Display
Page 22 and 23: 03 Basic Operations 3.2 Program You
Page 24 and 25: 03 Basic Operations 3.2.4 Assign a
Page 26 and 27: 04 Basic Picture Adjustment For sta
Page 28 and 29: 04 Basic Picture Adjustment 4.2 Sma
Page 30 and 31: 04 Basic Picture Adjustment 4.2.7 T
Page 32 and 33: 05 Additional Picture Adjustment Op
Page 46 and 47: 06 Use Other Equipment With Your Fl
Page 58 and 59:
06 Use Other Equipment With Your Fl
Page 60 and 61:
Page 62 and 63:
Page 64 and 65:
Page 66 and 67:
Page 68 and 69:
Page 70 and 71:
Page 72 and 73:
Page 74 and 75:
Page 76 and 77:
07 Helpful Information Why does the
Page 78 and 79:
07 Helpful Information Picture Issu
Page 80 and 81:
08 Cautions and Warnings 80 En 8 Ca
Page 82 and 83:
08 Cautions and Warnings In rare ca
Page 84 and 85:
08 Cautions and Warnings 8.9.2 Radi
Page 86 and 87:
09 Appendix 9.1.2 Satellite Brand/C
Page 88 and 89:
09 Appendix 9.1.3 VCR Brand/Code Br
Page 90 and 91:
09 Appendix Brand/Code Brand/Code B
Page 92 and 93:
09 Appendix 9.1.5 DVD-R Brand/Code
Page 94 and 95:
09 Appendix Brand/Code Brand/Code B
Page 96 and 97:
09 Appendix 9.2 Video/PC Signals (H
Page 98 and 99:
09 Appendix 9.2.4 INPUT 3 (D-Sub) -
Page 100 and 101:
09 Appendix Resolution Dot-Line Hf
Page 102 and 103:
09 Appendix 9.4 Trademarks Trademar
Page 104 and 105:
09 Appendix DHCP The Dynamic Host C
Page 106:
Register Your Product on http://www
show all

Operations Manual - PRO-101FD - Pioneer Electronics

Create successful ePaper yourself

Delete template?

Save as template?