Hydraulic Motors MVM Series - HANSA-TMP

Heavy Duty Orbit Motors (Disc Valve)
Hydraulic Motors MVM Series
CONTENTS
GENERAL
APPLICATION
Specification data .......................... 27
Dimensions and mounting ...............28
Shaft extensions ............................ 28
Permissible shaft Seal Pressure .... 29
Permissible shaft loads .................. 30
Order code ..................................... 30
»
»
»
»
»
»
»
Conveyors
Metal working machines
» Agriculture machines
Road building machines
Mining machinery
Food industries
Special vehicles
Plastic and rubber machinery etc.
OPTIONS
A
B
» Model- Disc valve, roll-gerotor
» Flange with wheel mount
» Short motor
» Side ports
» Shafts- straight, splined and tapered
» BSPP ports;
» Other special features.
EXCELLENCE
» High torque and pressure drop
» High inlet pressure
» High starting torque
» Improved efficiency at high pressure drop
» Smooth operation at low speed
» High radial and axial bearing capacity
3 3
Max. Displacement, cm /rev [in /rev]
Max. Speed,
[RPM]
Max. Torque,
daNm [lb-in]
Max. Output,
kW [HP]
Max. Pressure Drop,
bar [PSI]
Max. Oil Flow,
lpm [GPM]
Min. Speed,
[RPM]
Permissible Shaft Loads, daN [lbs]
Pressure fluid
O O
Temperature range,
C[ F]
2
Optimal Viscosity range, mm /s [SUS]
Filtration
Oil flow in drain line
801,8 [48.91]
736
cont.: 259 [22920] int.: 340 [30090]
112 [150]
cont.: 250 [3630]
int.: 350 [5080]
240 [ 63.4]
5
Pa=1500 [3370]
Mineral based- HLP(DIN 51524) or HM(ISO 6743/4)
-40÷140 [-40÷284]
20÷75 [ 98÷347]
ISO code 20/16 (Min. recommended fluid filtration of 25 micron)
Pressure Losses
Pressure drop
bar [ PSI]
200 [2900]
275 [ 3990]
Viscosity
Oil flow in
drain line
2
mm /s [ SUS]
lpm [ GPM]
20 [98] 2,5 [. 660]
35 [164] 1,5 [.
400]
20 [98] 4 [1.057]
35 [164] 2,5 [.660]
400
300
200
100
0
30
25
20
15
10
5
0
0 25 50 75 100 125 150 175 200
Q, lpm
0 5 10 15 20 25 30 35 40 45 50
Q, GPM
Pag. 26
HT 03 / E / 301 / 0211 / E

Heavy Duty Orbit Motors (Disc Valve)
MVM Motors
SPECIFICATION DATA
Type
MVM
315
MVM
400
MVM
500
MVM
630
MVM
800
Displacement,
3
3
cm /rev. [ in /rev. ]
Max. Speed,
[RPM]
Max. Torque
cont.
Int.*
cont.
daNm [ lb-in ]
Int.*
314,5 [ 19.18]
636
736
115 [ 10180]
160 [ 14160]
400,9 [ 24.5]
500
600
144 [ 12745]
200 [ 17700]
499,6 [30.5]
400
480
180 [ 15930]
260 [ 23010]
629,1 [ 38.38]
315
380
227 [ 20090]
310 [ 27440]
801,8 [ 48.91]
250
300
259 [ 22920]
340 [ 30090]
peak**
180 [ 15930]
230 [ 20355]
286 [ 25315]
360 [ 31860]
402 [ 35580]
Max. Output
cont.
67 [ 90]
67 [ 90]
67 [ 90]
67 [ 90]
67 [ 90]
kW [ HP]
int.*
112 [ 150]
112 [ 150]
112 [ 150]
112 [ 150]
112 [ 150]
Max. Pressure Drop
cont.
250 [ 3630]
250 [ 3630]
250 [ 3630]
250 [ 3630]
225 [ 3263]
bar [ PSI ]
Int.*
350 [ 5080]
350 [ 5080]
350 [ 5080]
350 [ 5080]
300 [ 4350]
peak**
400 [ 5800]
400 [ 5800]
400 [ 5800]
400 [ 5800]
350 [ 5080]
Max. Oil Flow
cont.
200 [ 52.8]
200 [ 52.8]
200 [ 52.8]
200 [ 52.8]
200 [ 52.8]
lpm [ GPM ]
Max. Inlet Pressure
bar [ PSI ]
Int.*
cont.
Int.*
peak**
240 [ 63.4]
270 [3915]
370 [ 5365]
420 [ 6090]
240 [ 63.4]
270 [3915]
370 [ 5365]
420 [ 6090]
240 [ 63.4]
270 [3915]
370 [ 5365]
420 [ 6090]
240 [ 63.4]
270 [3915]
370 [ 5365]
420 [ 6090]
240 [ 63.4]
270 [3915]
370 [ 5365]
420 [ 6090]
Max. Return Pressure
cont.
140 [2030]
140 [2030]
140 [2030]
140 [2030]
140 [2030]
with Drain Line
Int.*
175 [2540]
175 [2540]
175 [2540]
175 [2540]
175 [2540]
bar [PSI]
peak**
210 [3045]
210 [3045]
210 [3045]
210 [3045]
210 [3045]
Max. Starting Pressure with Unloaded Shaft,
bar [PSI]
Min. Starting Torque daNm [ lb-in]
Min. Speed***, [RPM]
Weight, kg [ lb]
5 [ 70]
92 [ 8140]
10
41,3 [ 91]
5 [ 70]
115 [10180]
6
42,1 [ 93]
5 [ 70]
144 [12745]
8
43 [ 95]
5 [ 70]
180 [15930]
6
44,5 [ 98]
5 [ 70]
205 [18145]
5
46 [ 101.4]
* Intermittent operation: the permissible values may occur for max. 10% of every minute.
** Peak load: the permissible values may occur for max. 1% of every minute.
*** For speeds lower than given, consult factory or your regional manager.
1. Intermittent speed and intermittent pressure must not occur simultaneously.
2. Recommended filtration is per ISO cleanliness code 20/16. A nominal filtration of 25 micron or better.
3. Recommend using a premium quality, anti-wear type mineral based hydraulic oil HLP(DIN51524) or HM ( ISO 6743/4).
If using synthetic fluids consult the factory for alternative seal materials.
4. Recommended minimum oil viscosity 13 mm²/s [70 SUS] at 50°C [122°F].
5. Recommended maximum system operating temperature is 82°C [180°F].
6. To assure optimum motor life fill with fluid prior to loading and run at moderate load and speed for 10-15 minutes.
HT 03 / E / 301 / 0211 / E Pag. 27

Heavy Duty Orbit Motors (Disc Valve)
MVM Motors
DIMENSIONS AND MOUNTING DATA
CO Shaft
C Shaft
SH Shaft
K Shaft
ø160 -0,063
[6.3 -.0025]
122 [4.8]
79 [3.11]
105 [4.134]
145 [5.71]
Shaft Dim.
See Page 29
1 1
+0,2
[ .433 +.0079 ]
20±0,3
[.787±.012]
L2
L
max
L1
P (A,B)
ø160 [6.299]
21±0,15
[.827±.0059]
T
50±0,15
[1.97±.0059]
50±0,15
[1.97±.0059]
15±0,15
[.59±.0059]
85 -0,5
[3.35 ] -.0196
Port A
160
[6.299]
Port B
ø200±0,4
[7.87±.016]
4xø18
[.708]
P (A,B)
T
Versions
2
4
5
2xG1 2x1 16 -12UN
G¼ -18UNF
9
16
179 [7.05]
Warning:
Drain line should always be used.
179 [7.05]
Type
L, mm [ in]
L, 2 mm [ in]
L, 1 mm [ in]
MVM 315
MVM 400
MVM 500
MVM 630
MVM 800
226,5 [8.92]
233,5 [9.19]
241,5 [9.51]
252 [9.92]
266 [10.47]
172,5 [6.79]
179,5 [7.07]
187,5 [7.38]
198 [7.79]
212 [8.35]
25,5 [1.00]
32,5 [1.28]
40,5 [1.59]
51 [2.01]
65 [2.56]
Standard Rotation
Viewed from Shaft End
Port A Pressurized - CW
Port B Pressurized -CCW
Reverse Rotation
Viewed from Shaft End
Port A Pressurized - CCW
Port B Pressurized -CW
mm [in]
Pag. 28
HT 03 / E / 301 / 0211 / E

]
-
]
-
-
]
-
-
]
-
-
]
-
Heavy Duty Orbit Motors (Disc Valve)
MVM Motors
SHAFT EXTENSIONS
C - ø50 straight, Parallel key A14x9x70 DIN 6885
CO - ø2 ¼"[57,15] straight,Parallel key ½ "x ½"x 2¼" BS46
14 -0,043
[.551-0017]
79 [3.11]
12,72-0,02
[.502 ] -.0008
79 [3.11]
ø 53
+0,5
[2.086
+0,2
+.0197
+.0079
ø60 [2.362]
ø 50
+0,018
+0,002
+.0008
+.0007
[1.968 ]
ø 62,9 2
[ 2.48 9
0,
.007
ø60 [2.362]
ø 57,15 5
[ 2.25 6
0,01
.000
M12
min 26 [1.024] deep
38-16UNC /
min 25 [.98] deep
SH
- ø2 / "splined, 16 DP 8/16 ANS B92.1-1976
1 8
K - tapered 1:10, Parallel key B16x10x32 DIN 6885
79 [3.11]
56 +2
[2.205 +.079 ]
A-A
16 -0,043
[.63 ] -.0017
70 [2.756]
A
40 [1.575]
7
[.275]
S=65
Tightening Torque
70±1 daNm
[6196±88.5 lb-in]
M12
min 26 [1.024] deep
ø60 [2.362]
ø53,975 5
[ 2.125 1
0,02
.00
32,25 2
[ 2.27 9
0,
.007
ø60 [2.362]
Taper 1:10
A
105 [4.134]
ø8
[.315]
6
[.236]
M42x3
ø78 [3.01]
mm [in]
MAX. PERMISSIBLE SHAFT SEAL PRESSURE
Max. return pressure without drain line or
max. pressure in the drain line
P
[PSI]
1000
750
500
P
[bar]
80
70
60
50
40
30
- continuous operations
- intermittent operations
250
0
20
10
0
0 50 100 150 200 250 300 350 400 450 500 550 600
n
[RPM]
HT 03 / E / 301 / 0211 / E Pag. 29

Heavy Duty Orbit Motors (Disc Valve)
MVM Motors
PERMISSIBLE SHAFT LOADS
The output shaft runs in tapered bearings that permit high axial and radial forces. Curve " 1" shows max. radial shaft
load. Any shaft load exceeding the values quoted in the curve will seriously reduce motor life. The two other curves
apply to a B10 bearing life of 3000 hours at 200 RPM.
Prad
daN
6000
5000
4000
4 3 2 1 0 -1
1500 daN
3370 lbs.
1500 daN
3370 lbs.
1
2
in
Prad
lbs
14000
12000
10000
2 -P=0 a daN [ 0 lbs]
3 - P a=1500 daN [ 3370 lbs]
8000
3000
3
6000
2000
4000
1000
2000
-125 -100 -75 -50 -25 0 25 50 mm
ORDER CODE
MVM
1 2 3 4 5 6
Pos.1 - Displacement code
315
400
500
630
800
Pos.2 - Shaft Extensions *
C
CO
SH
K
3
3
- 314,5 cm /rev [19.8 in /rev]
3
3
- 400,9 cm /rev [24.45 in /rev]
3
3
- 499,6 cm /rev [30.48 in /rev]
3
3
- 629,1 cm /rev [38.38 in /rev]
3
3
- 801,8 cm /rev [48.91 in /rev]
- ø50 straight, Parallel key A14x9x70 DIN6885
1
1 1 1
- ø2 /
4" straight, Parallel key /
2"x /
2"x2 /
4" DIN6885
1
- ø2 / 8" splined, ANS B92.1-1976
- ø60 tapered 1:10, Parallel key B16x10x32 DIN6885
Pos.3 - Ports
2
4
- side ports, 2xG1, G1/4, BSP thread, ISO 228
- side ports, 2x1 5/16-12 UN, O-ring, 9/16-18 UNF
Pos.4 - Check Valves
omit - without check valves
1 - with check valves
Pos.5 - Special Features (see page 35)
Pos.6 - Design Series
omit - Factory specified
NOTES:
* The permissible output torque for shafts must be not exceeded!
The hydraulic motors are mangano-phosphatized as standard.
Pag. 30
HT 03 / E / 301 / 0211 / E