Machine vices - Duroc AB

More documents

Recommendations

Info

Standard device BFS, mechanically operated For use by contract workers, tool and mould makers as well as for production. After removal of the central jaw, the system can be retrofitted with a stop plate (for accessories, see below) to cope with large clamping ranges 3 rd hand function for consecutive loading and unloading of workpieces Locating pin and drill hole for an exact positioning of the central jaw Aluminium jaws, suitable for complete milling out. Both sides may be used Hardened steel guides Base made from aluminium, hard anodized Large outlet for swarf and coolant Mechanical spindle Easy preparation for clamping, stop and contact surfaces in aluminium jaws which can be completely milled out. 24
This is the device we offer for clamping workpieces with complex clamping and contact contours. In many cases, expensive special clamping fixtures are no longer required. Instead of a complete new fixture just a new set of jaws may be used! The aluminium jaws can be completely milled out to suit the required workpiece contour. This gives the fastest jaw change without a screwed connection! The aluminium base with hardened steel guides results in a low dead weight. The third hand function ensures consecutive safe loading and unloading of workpieces. 46 102 178 SW 16 64 57 117 86 31 102 M10 (4x) 20 Max. 381 M8 (2x) 32 20 H7 / 6 deep (4x) Standard device TV 100 S.G. Supplied including a set of jaws, jaw width 100 mm, weight 14 kg Part no. 9.3452.0101 13 57 86 50 150 177 Ø 16 H7 (2x) Ø 12,8 102 102 63,5 Single set of jaws for type TV/MQS 100 Part no. 9.3452.5101 31 Stop plate TV 100 Required for retrofitting the device to cope with large clamping ranges Part no. 9.3452.6101 46 127 253 SW 16 76 89 123 86 37 152 20 Max. M10 (4x) 508 M10 (2x) 32 20 H7 / 6 deep (4x) Standard device TV 150 S.G. Supplied including a set of jaws, jaw width 150 mm, weight 30 kg Part no. 9.3454.0101 13 200 61 100 50 200 277 Ø 13 (6x) Ø 16 H7 (2x) Single set of jaws for type TV/MQS 150 Part no. 9.3454.5101 152 127 76 Stop plate TV 150 Required for retrofitting the device to cope with large clamping ranges Part no. 9.3454.6101 We will be pleased to provide more details. Please contact info@hilma.de 37 all dimensions in mm Jaw change in a few seconds without the need for additional tools or pins. Downthrust effect in the movable jaws. 25
Page 1 and 2: Machine vices and systems www.hilma
Page 3 and 4: Pages 4 - 5 Pages 6 - 9 Pages 10 -
Page 5 and 6: * For tool making, mould making, co
Page 7 and 8: t b* For tool making, mould making,
Page 9 and 10: Druck t For use in semi- or fully a
Page 11 and 12: For tool making, mould making, cons
Page 13 and 14: Load cell for types EL, NC, KNC for
Page 15 and 16: QIS Jaws b a QIS base jaw, with per
Page 17 and 18: SMV jaws Stop pin displaceable Clam
Page 19 and 20: l f f j i j a ±0.01 i j d e t G1 l
Page 21 and 22: Double clamping system DS 100 hydra
Page 23: DS125 Standard jaws DS 125 standard
Page 27 and 28: Our SERVICE, your ADVANTAGE Custome

Machine vices - Duroc AB

Create successful ePaper yourself

Delete template?

Save as template?