Phoenix 351, 401, 451, 551 Expert puls FDW - EWM Hightec ...

More documents

Recommendations

Info

Intended use Use and operation solely with the following machines 3.2 Use and operation solely with the following machines NOTE A suitable wire feed unit (system component) is required in order to operate the welding machine! Phoenix Expert 351, 401, 451, 551 drive 200C drive 300C drive 4L M3.00 drive 4L M3.70 drive 4 M3.00 drive 4 M3.70 M drive 4Z W 16 099-004833-EW501 10.07.2012
Intended use Documents which also apply 3.3 Documents which also apply 3.3.1 Warranty NOTE For further information, please see the accompanying supplementary sheets "Machine and Company Data, Maintenance and Testing, Warranty"! 3.3.2 Declaration of Conformity The designated machine conforms to EC Directives and standards in terms of its design and construction: • EC Low Voltage Directive (2006/95/EC), • EC EMC Directive (2004/108/EC), This declaration shall become null and void in the event of unauthorised modifications, improperly conducted repairs, non-observance of the deadlines for the repetition test and / or non-permitted conversion work not specifically authorised by the manufacturer. The original copy of the declaration of conformity is enclosed with the unit. 3.3.3 Welding in environments with increased electrical hazards In compliance with IEC / DIN EN 60974, VDE 0544 the machines can be used in environments with an increased electrical hazard. 3.3.4 Service documents (spare parts and circuit diagrams) DANGER Do not carry out any unauthorised repairs or modifications! To avoid injury and equipment damage, the unit must only be repaired or modified by specialist, skilled persons! The warranty becomes null and void in the event of unauthorised interference. • Appoint only skilled persons for repair work (trained service personnel)! Original copies of the circuit diagrams are enclosed with the unit. Spare parts can be obtained from the relevant authorised dealer. 099-004833-EW501 10.07.2012 17
Page 1 and 2: Operating instructions Welding mach
Page 3 and 4: Contents Notes on the use of these
Page 5 and 6: Contents Notes on the use of these
Page 7 and 8: Safety instructions Explanation of
Page 9 and 10: Safety instructions General WARNING
Page 11 and 12: Safety instructions General CAUTION
Page 13 and 14: Safety instructions Transport and i
Page 15: Intended use Applications 3 Intende
Page 19 and 20: Machine description - quick overvie
Page 25 and 26: Design and function Installation CA
Page 27 and 28: Design and function Welding torch c
Page 29 and 30: Design and function Mains connectio
Page 31 and 32: Design and function Shielding gas s
Page 33 and 34: Design and function MIG/MAG welding
Page 67 and 68:
Design and function MIG/MAG welding
Page 69 and 70:
Design and function Advanced functi
Page 71 and 72:
Page 73 and 74:
Page 75 and 76:
Design and function TIG welding 5.1
Page 77 and 78:
Page 79 and 80:
Page 81 and 82:
Design and function TIG welding Non
Page 83 and 84:
Design and function TIG welding Lat
Page 85 and 86:
Design and function MMA welding 5.1
Page 87 and 88:
Page 89 and 90:
Page 91 and 92:
Page 93 and 94:
Design and function Interfaces 5.14
Page 95 and 96:
6 Maintenance, care and disposal Ma
Page 97 and 98:
Maintenance, care and disposal Main
Page 99 and 100:
Rectifying faults Checklist for rec
Page 101 and 102:
Rectifying faults Resetting JOBs (w
Page 103 and 104:
Rectifying faults Vent coolant circ
Page 105 and 106:
Technical data Phoenix 351, 451, 55
Page 107 and 108:
Accessories Computer communication
Page 109 and 110:
Appendix A JOB-List Job-Nr./ job-no
Page 111 and 112:
Page 113 and 114:
Page 115 and 116:
Page 117 and 118:
show all

Phoenix 351, 401, 451, 551 Expert puls FDW - EWM Hightec ...

You also want an ePaper? Increase the reach of your titles

Delete template?

Save as template?