7. operating the zpm - Grass

More documents

Recommendations

Info

7. OPERATING THE ZPM Illustration 7-008-01 Illustration 7-008-02 Illustration 7-009-01 Illustration 7-009-02 28 The star in your cabinet
7. OPERATING THE ZPM 7-008 Setting the Front Height Stops Illustration 7-008-01, 02 The stop pins „1“ of the front height stops „2“ can be moved in a vertical direction. With unnecessary front height stops „2“, the stop pins are simply pressed down. They can be pushed up whenever they are needed without any problem. After the following are correctly set; - drawer width according to Section 7-203 - drawer length according to Section 7-206 - back wall height according to Section 7-207, the front height stops can be set. Start with the lowest drawer front. - Slide the unit carrier to the front of the respective drawer width. - Open both toggle levers „8“. - Place a front panel „3“ on both front supports „4“. - Place a drawer bottom „8“ (with the bottom groove towards the machine operator). - Place a drawer back wall „6“ on the back wall support. - Insert Zargen slides „7“ , left and right - Close both toggle levers „8“. - Lift both Zargen slides „7“ so that the Zargen slide dowel is about 30 mm away from the front „3“. - Hang up the setting gauge „9“ with the respective page ( 6035 = larger distance of Zargen 6035; 6036 = smaller distance for all other Zargen heights) in the drawer bottom’s dowel hole which is closest to the front. - Press the setting gauge „9“ (Notch) against the drawer bottom „5“ (corner). - Loosen the flap screw „10“ of the front height stop „2“. Slide the front height stop against the drawer front „3“. Tighten the flap screw „10“. - Repeat the same on the second side of the Zargen press. Front height stops can be set in desired quantities, but there must be a minimum distance of about 15 mm. Smaller distances can lead to problems with the flap screws. In this case, the flap screws can be replaced by Allen screws M6 X 16. Five front height stops are included in the standard equipment. Additional height stops can be obtained as accessories. 7-009 Setting the Front Side Stops Illustration 7-009-01, 02 After the front height stops are set, according to Section 7-208, the front side stops are set. - Drawer front, bottom, back wall and both Zargen slides are placed in the machine. Close both toggle levers. - Hang the setting gauge „9“ with the respective side ( 6035 for Zargen 6035, 6036 for all other Zargen heights ) in the drawer bottom’s dowel hole, which is closest to the front „3“. - Press the setting gauge „9“ (notch) against the drawer bottom „3“ ( corner ). - Loosen the flap screw „11“ of the left front side stop „12“. Slide the stops against the drawer front „3“ (between the front and stop, there should be a gap of 0.2 to 0.5 mm). Tighten the flap screw „11“. - Loosen the flap screw „15“ of the setting collar „13“ on the right spring loaded front side stop. Slide the setting collar against the guide tube „14“ of the front side stop. - Tighten the flap screw „15“. ( There should be a gap of 0.5 mm to 1 mm between the setting collar and the guide tube. The set gap, left and right, serves to balance out the tolerances of the drawer front production). Front side stops can only be set for a front overhang. The star in your cabinet 29
Page 1 and 2: OPERATING INSTRUCTIONS Grass ZPM Th
Page 3 and 4: TABLE OF CONTENTS 1. General 5-6 1-
Page 5 and 6: LIST OF ILLUSTRATIONS 1-001 List of
Page 7 and 8: 2. SAFETY INFORMATION 2-001 Safety
Page 9 and 10: 2. SAFETY INFORMATION 2-005 Descrip
Page 11 and 12: 3. DESCRIPTION OF PRODUCTS 3-001 Us
Page 13 and 14: 4. DESCRIPTION OF MACHINE COMPONENT
Page 19 and 20: 5. SHIPPING AND INSTALLATION OF MAC
Page 21 and 22: 6. START-UP 6 7 5 4 2 14 12 4 A 5 1
Page 23 and 24: 7. OPERATING THE ZPM 7-001 Checking
Page 25 and 26: 7. OPERATING THE ZPM 7-002 Mounting
Page 27: 7. OPERATING THE ZPM 7-004 Changing
Page 31 and 32: 7. OPERATING THE ZPM 7-010 Setting
Page 33 and 34: 7. OPERATING THE ZPM 7-012 Setting
Page 35 and 36: 8. TROUBLE SHOOTING AND PROBLEM SOL
Page 37 and 38: 10. MISCELLANEOUS 10-001 Guarantee
Page 39 and 40: 10. MISCELLANEOUS 10-002 Disposal F
Page 41 and 42: 10. MISCELLANEOUS 1-003 Resale Form
Page 43 and 44: 10. MISCELLANEOUS 10-004 Questionna
Page 45 and 46: 10. MISCELLANEOUS 10-004 Questionna
Page 47 and 48: REPRESENTATIVES AROUND THE WORLD Au

7. operating the zpm - Grass

Create successful ePaper yourself

Delete template?

Save as template?