A152-20-5 - Teledyne Relays

More documents

Recommendations

Info

SERIES A152 TYPICAL RF INSERTION LOSS REPEATABILITY CHARACTERISTICS (Notes 1 and 3) 0.2 A152 Insertion Loss Repeatability (Through Path) IL Repeatability (dB) 0.1 0 • Data represents 1 sample of A152-20-5 • Relay was cycled at 5 Hz and IL was measured at every 10K cycles up to 1M cycles. Data presented is with respect to the first sweep. • Relay was tested on a fixture made by Microtest Inc. • HP 8719D VNA was used for measurements • Test was performed at room temperature. • RF input power level 10dBm -0.1 0.0 0.3 0.6 0.9 1.2 1.5 1.8 2.1 2.4 2.7 3.0 3.3 3.6 3.9 4.2 4.5 4.8 5.0 Frequency (GHz) IL Repeatability (dB) A152 Insertion Loss Repeatability (Attenuated Path) 1 0.9 0.8 • Data represents 1 sample of A152-20-5 0.7 • Relay was cycled at 5 Hz and IL was measured at every 10K cycles 0.6 up to 1M cycles. Data presented is with respect to the first sweep. • Relay was tested on a fixture made by Microtest Inc. 0.5 • HP 8719D VNA was used for measurements 0.4 • Test was performed at room temperature. 0.3 • RF input power level 10dBm 0.2 0.1 0 -0.1 -0.2 0.0 0.3 0.6 0.9 1.2 1.5 1.8 2.1 2.4 2.7 3.0 3.3 3.6 3.9 4.2 4.5 4.8 5.0 Frequency (GHz) RF INSERTION LOSS REPEATABILITY NOTES 1. Test conditions: a. Fixture: Custom plug-in test fixture. b. Relay header is in contact with, but not soldered to, ground plane. c. Test performed at room ambient temperature. d. Contact signal level: 10 dBm. 2. Data presented herein represents typical characteristics and is not intended for use as specification limits. 3. Insertion loss repeatability measured over frequency range from 3 MHz to 5 GHz. A152 Page 4 SPECIFICATIONS ARE SUBJECT TO CHANGE WITHOUT NOTICE © 2006 TELEDYNE RELAYS A152\042006\Q1
Appendix A: Spacer Pads Pad designation and bottom view dimensions Ø.150 [3.81] (REF) “M4” Pad for TO-5 Dim H MAX Height For use with the following: Dim. H Max. ER411T ER412, ER412D, ER412DD .295 (7.49) 712, 712D, 712TN, RF300, RF310, RF320 .300 (7.62) ER420, ER422D, ER420DD, 421, ER421D, ER421DD, ER422, ER422D, .305 (7.75) ER422DD, 722, 722D, RF341 ER431T, ER432T, ER432, ER432D, ER432DD .400 (10.16) 732, 732D, 732TN, RF303, RF313, RF323 .410 (10.41) RF312 .350 (8.89) ER411, ER411D, ER411DD .295 (7.49) Dim H MAX ER431, ER431D, ER431DD .400 (10.16) RF311 .300 (7.62) “M4” Pad for TO-5 RF331 .410 (10.41) “M4” Pad for Centigrid ® RF103 .420 (10.67) 172, 172D .305 (7.75) ER114, ER114D, ER114DD, Dim H MAX J114, J114D, J114DD .300 (7.62) ER134, ER134D, ER134DD, J134, J134D, J134DD .400 (10.16) RF100 .315 (8.00) .156 [3.96] (REF) “M9” Pad for Centigrid ® A150 .305 (7.75) 122C, A152 .320 (8.13) Dim H ER116C, J116C .300 (7.62) MAX ER136C, J136C .400 (10.16) RF180 .325 (8.25) .256 [6.5] (REF) Notes: 1. Spacer pad material: Polyester lm. 2. To specify an “M4” or “M9” spacer pad, refer to the mounting variants portion of the part numbering example in the applicable datasheet. 3. Dimensions are in inches (mm). 4. Unless otherwise specied, tolerance is ± .010 (.25). 5. Add 10 m to the contact resistance show in the datasheet. 6. Add 0.01 oz. (0.25 g) to the weight of the relay assembly shown in the datasheet. © 2008 Teledyne Relays SPECIFICATIONS SUBJECT TO CHANGE WITHOUT NOTICE
Page 1 and 2: HIGH REPEATABILITY ULTRAMINIATURE B
Page 3: RF PERFORMANCE (-55°C to +85°C, u
Page 7: Appendix A: Ground Pin Positions Ø

A152-20-5 - Teledyne Relays

Create successful ePaper yourself

Delete template?

Save as template?