1 - A.O. Smith Water Heaters

More documents

Recommendations

Info

How to Use (Using the remote controller) Flow Meter Alarm 2,3 1 3 Preparation 1 (Starting with the power off) Press the Power On/Off Button 2Set temperature. ( Always check temperature setting) before use. 1. Plug the bath drain. On Hot Cold The temperature will be displayed on the remote control thermostat. On Check the indicator lights. Previous set temperature (example:110°F) <strong>Water</strong> temperature 14
An alarm will sound for ten seconds when the flow reaches the set level. <strong>Water</strong> Temperature The temperatures settings below are only examples. The temperature setting necessary will depend on the usage, the length of piping and the time of year. (°F: ) 100 105 110 115 120 Warm Warmer Hot The water will continue to run unless it is manually turned off. * Initial factory setting: 110°F To set the flow meter alarm: 3 Adjust flow meter alarm setting. 4 Turn on hot water. 5 Turn off the hot water when the alarm sounds. Press the flow meter alarm set button (the setting will flash on the display) and adjust with the setting buttons. The alarm will sound when the set level has been reached. Stop the water. Increase Decrease Choose the flow meter alarm setting from the following options: 10 - 60 (In 5 gallon intervals), 70 - 100 (In 10 gallon intervals), or 990 gallons. Note: The alarm will not sound if it is set for 990 gal. On Note: The alarm will not sound if it is set for 990 gal. Off Flow meter setting will be flashing (ex. 45 gal.) * The level can only be adjusted while the indicator is flashing. * After ten seconds, the remote will again display the temperature. If the flow meter alarm is being used to indicate when a tub is full: • If any hot water is being used besides what is going into the tub, the alarm will sound before the tub is full. • If there was water in the tub before the fill began, or if the water is not shut off manually when the alarm sounds, the tub may overflow. • If there was water in the tub before the fill began, the temperature in the tub after it is full may be different from the temperature setting. 15
Page 1 and 2: Owner’s Guide and Installation Ma
Page 3 and 4: Important Safety Information-1 To p
Page 5 and 6: Caution Be sure to electrically gro
Page 7 and 8: General Parts-1 Main Unit Indoor/Ou
Page 9 and 10: General Parts-3 Display The illustr
Page 11 and 12: How to Use (Using the remote contro
Page 13: 2 Set temperature. 3 Turn on hot Tu
Page 17 and 18: Preventing Damage from Freezing-2 I
Page 19 and 20: Regular Maintenance-2 Periodic Main
Page 21 and 22: Troubleshooting-2 Temperature The w
Page 23 and 24: Troubleshooting-4 Check for an Erro
Page 25 and 26: Specifications •Specifications ma
Page 27 and 28: External outfitting Part Nos. Part
Page 29 and 30: Combustion unit and gas route Part
Page 31 and 32: Hot-water feed route Part Nos. Part
Page 33 and 34: Electronic control unit, Remote con
Page 35 and 36: 1. Included Accessories The followi
Page 37 and 38: 4. Before Installation Caution Chec
Page 39 and 40: Securing of space for repair/inspec
Page 41 and 42: Clearance Requirements from Vent Te
Page 43 and 44: 8. Vent Pipe Installation (Indoor I
Page 45 and 46: Combustion Air Supply combustion ai
Page 47 and 48: Gas Line Sizing Adapted from UPC 19
Page 49 and 50: 11. Plumbing Applications Cold Wate
Page 51 and 52: Remote Controller • Applicable Mo
Page 53 and 54: Pump Wiring * This feature is not a
Page 55 and 56: Caution Handling after trial operat
Page 57 and 58: WIRING DIAGRAM MAIN WATER FLOW CONT
Page 59 and 60: Remote Controller Installation Guid
Page 61: Installing the Remote Controller Ou

1 - A.O. Smith Water Heaters

You also want an ePaper? Increase the reach of your titles

Delete template?

Save as template?