Metallic Expansion Joints - Thorburn Flex Inc
Metallic Expansion Joints - Thorburn Flex Inc
Metallic Expansion Joints - Thorburn Flex Inc
Create successful ePaper yourself
Turn your PDF publications into a flip-book with our unique Google optimized e-Paper software.
THORBURN<br />
FLEXIBLE PIPING SPECIALIST<br />
DUAL-FLEX<br />
HOW TO ORDER FROM THIS CATALOGUE<br />
Nominal Model Style Series Plies Ends Pressure Bellows Ends Liner Spool Cover Access. O.A.L.<br />
size or cons # psi Material Material Material Material Material Material inches<br />
24 DF T A 2P FF 150 B5 E1 L5 S0 C0 T0 34.5<br />
24" I.D.<br />
Dual-<strong>Flex</strong><br />
Tied-restrained<br />
Movement Series A or<br />
specify cons i.e. 5C5C<br />
for 5 cons x 5 cons<br />
Blank for 1 ply<br />
or # of plies<br />
Flanged/Flanged<br />
Please refer to pages 50 to 52<br />
for specifications<br />
For material codes, please see page 12<br />
For movement specifications for Model DFP,<br />
please see Single-<strong>Flex</strong> pages 36 to 43<br />
WARNING<br />
Liners are mandatory if flow velocities exceed<br />
the following values:<br />
Air, steam and other gases<br />
1) Up to 6" dia. -4 ft/sec per inch of dia.<br />
2) Above 6" dia. -25 ft/sec<br />
Water and other liquids<br />
1) Up to 6" dia. -1-2/3 ft/sec. per inch of dia.<br />
2) Over 6" dia. -10 ft/sec.<br />
150 psi<br />
Bellows 321SS<br />
Ends 304SS<br />
Liner 321SS<br />
Spool<br />
Accessories<br />
Carbon Steel<br />
T = Tie rods<br />
Cover<br />
I = Intermediate anchor<br />
Carbon Steel<br />
H<br />
G<br />
= Hinge support<br />
= Gimbal support<br />
Accessories i.e. Tie<br />
rod plates Carbon Steel<br />
O.A.L. 34.5<br />
STANDARD MATERIALS<br />
(unless specified otherwise)<br />
Bellows: ASTM A240T321 (B5)<br />
Flanges: Carbon steel A105 or Plate A36 or 44W (customer should specify<br />
actual flanges required, i.e. drilling, material, type) (E0)<br />
Weld ends: Carbon steel A53, A106, Plate A36 or 44W (customer should specify<br />
actual weld ends required i.e. schedule, material, thickness, etc.) (E0)<br />
Vitaulic ends: Carbon steel A53, A106, A36, 44W (E0)<br />
Collars: Carbon steel A36/44W (E0)<br />
Liners: ASTM A240T321 (L5)<br />
Covers: Carbon steel A36/44W (C0)<br />
Accessories: Tie rods, Gimbal, hinges: Carbon steel (T0)<br />
OPTIONS<br />
Liner<br />
To specify liners add L as shown to part number and advise of specific movements<br />
to properly size liner. On combination ends specify flow direction.<br />
Cover<br />
To specify covers add C as shown to part number<br />
NOTES<br />
1. Rated cycle life for a standard Dual-<br />
<strong>Flex</strong> joint is 5000 cycles per EJMA<br />
6th ed. for any one movement<br />
tabulated minimum.<br />
2. To combine axial and lateral<br />
movements, the sum % of each must<br />
not exceed 100%. Refer to pages 50<br />
to 52.<br />
3. To obtain greater movements or cycle<br />
life contact <strong>Thorburn</strong>.<br />
4. Maximum axial extension movement<br />
is 50% of tabulated axial value.<br />
5. Maximum test pressure: 1-1/2 x rated<br />
working pressure.<br />
6. Catalogue pressure ratings are<br />
based upon a design temperature<br />
range of -20ºF to 800ºF. Actual<br />
operating temperature should always<br />
be specified.<br />
7. For higher pressure temperature,<br />
movement and cycle ratings with your<br />
application, contact <strong>Thorburn</strong>.<br />
Page 49