dtc b0112/41 short in side squib (rh) circuit - Highlander Club
dtc b0112/41 short in side squib (rh) circuit - Highlander Club
dtc b0112/41 short in side squib (rh) circuit - Highlander Club
You also want an ePaper? Increase the reach of your titles
YUMPU automatically turns print PDFs into web optimized ePapers that Google loves.
DIAGNOSTICS<br />
-<br />
SUPPLEMENTAL RESTRAINT SYSTEM<br />
DTC B0112/<strong>41</strong> SHORT IN SIDE SQUIB (RH) CIRCUIT (TO<br />
GROUND)<br />
05-1269<br />
0525N-16<br />
CIRCUIT DESCRIPTION<br />
The <strong>side</strong> <strong>squib</strong> RH <strong>circuit</strong> consists of the airbag sensor assy center and the separate type front seat back<br />
assy (<strong>side</strong> <strong>squib</strong> RH).<br />
The <strong>circuit</strong> <strong>in</strong>structs the SRS to deploy when deployment conditions are met.<br />
DTC B0112/<strong>41</strong> is recorded when a <strong>short</strong> to ground is detected <strong>in</strong> the <strong>side</strong> <strong>squib</strong> RH <strong>circuit</strong>.<br />
DTC No. DTC Detect<strong>in</strong>g Condition Trouble Area<br />
B0112/<strong>41</strong><br />
WIRING DIAGRAM<br />
see page 05-1263 .<br />
Short <strong>circuit</strong> <strong>in</strong> <strong>side</strong> <strong>squib</strong> (RH) wire harness (to ground)<br />
Side <strong>squib</strong> (RH) malfunction<br />
Airbag sensor assy center malfunction<br />
INSPECTION PROCEDURE<br />
1 CHECK FLOOR WIRE(SIDE SQUIB RH CIRCUIT)<br />
Separate type front seat back assy (Side <strong>squib</strong> RH)<br />
Airbag sensor assy center<br />
Floor wire<br />
Floor Wire<br />
Side Squib RH<br />
C<br />
D B<br />
A<br />
Airbag<br />
Sensor<br />
Assy<br />
Center<br />
S19<br />
(a)<br />
(b)<br />
(c)<br />
(d)<br />
Turn the ignition switch to the LOCK position.<br />
Disconnect the negative (-) term<strong>in</strong>al cable from the battery,<br />
and wait for at least 90 seconds.<br />
Disconnect the connectors from the airbag sensor assy<br />
center and the separate type front seat back assy (<strong>side</strong><br />
<strong>squib</strong> RH).<br />
Measure the resistance accord<strong>in</strong>g to the value(s) <strong>in</strong> the<br />
table below.<br />
Standard:<br />
SFR+<br />
SFR-<br />
Tester connection Condition Specified condition<br />
S19-1 (SFR+) -<br />
Body ground<br />
Always<br />
1 MΩ or Higher<br />
H40977<br />
H01019<br />
H42497<br />
H42849<br />
S19-2 (SFR-) -<br />
Body ground<br />
NG<br />
Always<br />
REPAIR OR REPLACE FLOOR WIRE<br />
1 MΩ or Higher<br />
OK<br />
2005 HIGHLANDER REPAIR MANUAL (RM1144U)<br />
Author:<br />
Date:<br />
1459
05-1270<br />
DIAGNOSTICS<br />
-<br />
SUPPLEMENTAL RESTRAINT SYSTEM<br />
2 CHECK AIR BAG SENSOR ASSY CENTER<br />
Side Squib RH<br />
S19<br />
SFR+<br />
CG<br />
H01020<br />
H42496<br />
H10600<br />
H01067<br />
TC<br />
D<br />
Floor Wire<br />
C<br />
SFR-<br />
Airbag<br />
Sensor<br />
Assy<br />
Center<br />
Service Wire<br />
DLC3 DTC B0112/<strong>41</strong><br />
H42851<br />
(a) Connect the connector to the airbag sensor assy center.<br />
(b) Us<strong>in</strong>g a service wire, connect S19-1 (SFR+) and S19-2<br />
(SFR-) of connector ”C”.<br />
NOTICE:<br />
Do not forcibly <strong>in</strong>sert a service wire <strong>in</strong>to the term<strong>in</strong>als of the<br />
connector when connect<strong>in</strong>g.<br />
(c) Connect the negative (-) term<strong>in</strong>al cable to the battery,<br />
and wait for at least 2 seconds.<br />
(d) Turn the ignition switch to the ON position, and wait for at<br />
least 60 seconds.<br />
(e) Clear the DTCs stored <strong>in</strong> memory (see page 05-1215 ).<br />
(f) Turn the ignition switch to the LOCK position.<br />
(g) Turn the ignition switch to the ON position, and wait for at<br />
least 60 seconds.<br />
(h) Check the DTCs (see page 05-1215 ).<br />
OK:<br />
DTC B0112/<strong>41</strong> is not output.<br />
HINT:<br />
Codes other than code B0112/<strong>41</strong> may be output at this time, but<br />
they are not related to this check.<br />
NG<br />
REPLACE AIR BAG SENSOR ASSY CENTER<br />
(SEE PAGE 60-53 )<br />
OK<br />
2005 HIGHLANDER REPAIR MANUAL (RM1144U)<br />
Author:<br />
Date:<br />
1460
DIAGNOSTICS<br />
-<br />
SUPPLEMENTAL RESTRAINT SYSTEM<br />
05-1271<br />
3 CHECK SEPARATE TYPE FRONT SEAT BACK ASSY(SIDE SQUIB RH)<br />
Side Squib RH<br />
DC<br />
DLC3<br />
CG<br />
H01021<br />
H10600 H01067<br />
TC<br />
Airbag<br />
Sensor<br />
Assy<br />
Center<br />
DTC B0112/<strong>41</strong><br />
H40983<br />
(a) Turn the ignition switch to the LOCK position.<br />
(b) Disconnect the negative (-) term<strong>in</strong>al cable from the battery,<br />
and wait for at least 90 seconds.<br />
(c) Disconnect the service wire from connector ”C”.<br />
(d) Connect the connector to the separate type front seat<br />
back assy (<strong>side</strong> <strong>squib</strong> RH).<br />
(e) Connect the negative (-) term<strong>in</strong>al cable to the battery,<br />
and wait for at least 2 seconds.<br />
(f) Turn the ignition switch to the ON position, and wait for at<br />
least 60 seconds.<br />
(g) Clear the DTCs stored <strong>in</strong> memory (see page 05-1215 ).<br />
(h) Turn the ignition switch to the LOCK position.<br />
(i) Turn the ignition switch to the ON position, and wait for at<br />
least 60 seconds.<br />
(j) Check the DTCs (see page 05-1215 ).<br />
OK:<br />
DTC B0112/<strong>41</strong> is not output.<br />
HINT:<br />
Codes other than code B0112/<strong>41</strong> may be output at this time, but<br />
they are not related to this check.<br />
NG<br />
REPLACE SEPARATE TYPE FRONT SEAT<br />
BACK ASSY (SEE PAGE 72-1 1, 72-19 )<br />
OK<br />
USE SIMULATION METHOD TO CHECK<br />
HINT:<br />
Before perform<strong>in</strong>g the simulation method, check that the airbag sensor assy center is <strong>in</strong> check mode<br />
(see page 05-1218 ).<br />
Perform the simulation method by select<strong>in</strong>g the check mode with the hand-held tester (see page<br />
05-1218 ).<br />
After select<strong>in</strong>g the check mode, perform the simulation method by wiggl<strong>in</strong>g each connector of the airbag<br />
system or driv<strong>in</strong>g the vehicle on a city or rough road (see page 05-1218 ).<br />
2005 HIGHLANDER REPAIR MANUAL (RM1144U)<br />
Author:<br />
Date:<br />
1461