- Page 1: Instruction Manual SMC 186-188/TSMC
- Page 5 and 6: 1. If the compressor is operational
- Page 7 and 8: First Aid for Accidents with Ammoni
- Page 9 and 10: Protecting the Operator as well as
- Page 11 and 12: Cooling Media Salt solutions (brine
- Page 13 and 14: the ring-plate type, are mounted at
- Page 15 and 16: S -- BFO 3-4-5 CMO - TCMO and SMC -
- Page 17 and 18: Vibration Data for Compressors - Al
- Page 19 and 20: Note the following, however: S S at
- Page 21 and 22: SCREW COMPRESSORS Evaporating tempe
- Page 23 and 24: T245400_0/2 Condensing temperature
- Page 25 and 26: Condensing temperature TC °F °C 1
- Page 27 and 28: General operating instructions for
- Page 29 and 30: Stopping plant for lengthy periods
- Page 31 and 32: For a satisfactorily performed evac
- Page 33 and 34: Servicing the reciprocating compres
- Page 35 and 36: No. 1 2 3 Scheduled services Operat
- Page 37 and 38: No. Operating Hours < 1200 rpm Oper
- Page 39 and 40: the crankcase, refrigeration oil ma
- Page 41 and 42: Charging the compressor with oil Co
- Page 43 and 44: The analysis The following table st
- Page 45 and 46: Pressure and temperature settings f
- Page 47 and 48: Servicing the Refrigeration Plant B
- Page 49 and 50: Maintenance of piston compressor Ge
- Page 51 and 52: Mounting top and water covers SMC 1
- Page 53 and 54:
Marked with LP or HP S S Tighten bo
- Page 55 and 56:
S Press cylinder lining down manual
- Page 57 and 58:
2. Needle bearing Needle bearing ty
- Page 59 and 60:
Dismanting of needle bearing S Use
- Page 61 and 62:
Shaft seal 10L 10M 10H 10J 8B 8A 8C
- Page 63 and 64:
the crankshaft is should be checked
- Page 65 and 66:
Compressor lubricating system 19D 1
- Page 67 and 68:
S Strip oil pump down by dismantlin
- Page 69 and 70:
By-pass valve pos. 24 The compresso
- Page 71 and 72:
Oil filter All oil to the lubricati
- Page 73 and 74:
Stop valves AK AC A AJ L P K R AD E
- Page 75 and 76:
Unloaded start and capacity regulat
- Page 77 and 78:
Pilot solenoid valves The pilot sol
- Page 79 and 80:
Standard unloaded start and capacit
- Page 81 and 82:
Service It will normally not be nec
- Page 83 and 84:
Stop valves pos. 23 and 42 23A 23G
- Page 85 and 86:
Clearance volume ”X” HPC SMC 10
- Page 87 and 88:
Pressure gauges The analog instrume
- Page 89 and 90:
Undersize Bearing Diameters for Cra
- Page 91 and 92:
Torque moments for screws and bolts
- Page 93 and 94:
Refrigeration Plant Maintenance Ope
- Page 95 and 96:
Trouble-shooting on the Piston Comp
- Page 97 and 98:
Code Case Code Case 1 No power - ma
- Page 99 and 100:
3. Compressor starts but stops agai
- Page 101 and 102:
7. Liquid stroke in compressor duri
- Page 103 and 104:
11. Excessive suction pressure 11.2
- Page 105 and 106:
15. Too low discharge pipe temperat
- Page 107 and 108:
Selecting Lubricating Oil for SABRO
- Page 109 and 110:
answer for the quality, the stabili
- Page 111 and 112:
Example (recip. compressors): Refri
- Page 113 and 114:
Data Sheet for Listed Sabroe Oils T
- Page 115 and 116:
R717 one-stage reciprocating compre
- Page 117 and 118:
R717 HPO og HPC reciprocating compr
- Page 119 and 120:
R22 two-stage reciprocating compres
- Page 121 and 122:
R134a two-stage reciprocating compr
- Page 123 and 124:
R407C two-stage reciprocating compr
- Page 125 and 126:
R404A two-stage reciprocating compr
- Page 127 and 128:
R507 one-stage reciprocating compre
- Page 129 and 130:
R717 screw compressors TC ° F °C
- Page 131 and 132:
R22 screw compressors with roller b
- Page 133 and 134:
R404A screw compressors ° F 104 TC
- Page 135 and 136:
R507 screw compressors TC ° F ° C
- Page 137 and 138:
Alignment of unit, AMR coupling Whe
- Page 139 and 140:
Installing directly on foundation W
- Page 141 and 142:
Preliminary installation Alignment
- Page 143 and 144:
Boring of motor flange for AMR coup
- Page 145 and 146:
question, as stated in the table. T
- Page 147 and 148:
Oil return to the compressor The se
- Page 149 and 150:
: Float valve controlled oil return
- Page 151 and 152:
Connections on TSMC 188 1 AC Y 1 Z
- Page 153 and 154:
Schematic diagram Parallel system,
- Page 155 and 156:
Water-cooling of reciprocating comp
- Page 157 and 158:
Cooling of top and side covers SMC
- Page 159 and 160:
Cooling of top and side covers SMC
- Page 161 and 162:
Necessary water consumption To achi
- Page 163 and 164:
Cooling of intermediate gas on TCMO
- Page 165 and 166:
It is essential to make sure that t
- Page 167 and 168:
Adjusting the TEAT valve: For both
- Page 169:
Spare parts sets for compressors an