15-B Operation (Mach Ctr), GFZ-62564E-1/02

More documents

Recommendations

Info

SAFETY PRECAUTIONS B–62564E–1/02 1 DEFINITION OF WARNING, CAUTION, AND NOTE This manual includes safety precautions for protecting the user and preventing damage to the machine. Precautions are classified into Warning and Caution according to their bearing on safety. Also, supplementary information is described as a Note. Read the Warning, Caution, and Note thoroughly before attempting to use the machine. WARNING Applied when there is a danger of the user being injured or when there is a damage of both the user being injured and the equipment being damaged if the approved procedure is not observed. CAUTION Applied when there is a danger of the equipment being damaged, if the approved procedure is not observed. NOTE The Note is used to indicate supplementary information other than Warning and Caution. Read this manual carefully, and store it in a safe place. s–2
B–62564E–1/02 2 GENERAL WARNINGS AND CAUTIONS SAFETY PRECAUTIONS WARNING 1. Never attempt to machine a workpiece without first checking the operation of the machine. Before starting a production run, ensure that the machine is operating correctly by performing a trial run using, for example, the single block, feedrate override, or machine lock function or by operating the machine with neither a tool nor workpiece mounted. Failure to confirm the correct operation of the machine may result in the machine behaving unexpectedly, possibly causing damage to the workpiece and/or machine itself, or injury to the user. 2. Before operating the machine, thoroughly check the entered data. Operating the machine with incorrectly specified data may result in the machine behaving unexpectedly, possibly causing damage to the workpiece and/or machine itself, or injury to the user. 3. Ensure that the specified feedrate is appropriate for the intended operation. Generally, for each machine, there is a maximum allowable feedrate. The appropriate feedrate varies with the intended operation. Refer to the manual provided with the machine to determine the maximum allowable feedrate. If a machine is run at other than the correct speed, it may behave unexpectedly, possibly causing damage to the workpiece and/or machine itself, or injury to the user. 4. When using a tool compensation function, thoroughly check the direction and amount of compensation. Operating the machine with incorrectly specified data may result in the machine behaving unexpectedly, possibly causing damage to the workpiece and/or machine itself, or injury to the user. 5. The parameters for the CNC and PMC are factory–set. Usually, there is not need to change them. When, however, there is not alternative other than to change a parameter, ensure that you fully understand the function of the parameter before making any change. Failure to set a parameter correctly may result in the machine behaving unexpectedly, possibly causing damage to the workpiece and/or machine itself, or injury to the user. 6. Immediately after switching on the power, do not touch any of the keys on the MDI panel until the position display or alarm screen appears on the CNC unit. Some of the keys on the MDI panel are dedicated to maintenance or other special operations. Pressing any of these keys may place the CNC unit in other than its normal state. Starting the machine in this state may cause it to behave unexpectedly. 7. The operator’s manual and programming manual supplied with a CNC unit provide an overall description of the machine’s functions, including any optional functions. Note that the optional functions will vary from one machine model to another. Therefore, some functions described in the manuals may not actually be available for a particular model. Check the specification of the machine if in doubt. s–3
Page 1 and 2: GE Fanuc Automation Computer Numeri
Page 3: SAFETY PRECAUTIONS This section des
Page 7 and 8: B-62564E-1/02 3 WARNINGS AND CAUTIO
Page 9 and 10: B-62564E-1/02 SAFETY PRECAUTIONS 4
Page 11 and 12: B-62564E-1/02 SAFETY PRECAUTIONS 5
Page 13 and 14: B-62564E-1/02 SAFETY PRECAUTIONS WA
Page 15 and 16: PREFACE B-62564E-1/02 Manuals relat
Page 17 and 18: 4.9.3 Rotational handle feed around
Page 19 and 20: 10.5 Read/Punch Function for Custom
Page 21 and 22: 11.13.5 Editing a displayed wavefor
Page 23 and 24: 4.2 Explanation of RS-422 Interface
Page 25 and 26: B-62564E-1/02 1. INTRODUCTION 1. IN
Page 27 and 28: B-62564E-1/02 1. INTRODUCTION (ii)
Page 29 and 30: B-62564E-1/02 1. INTRODUCTION (iii)
Page 31 and 32: B-62564E-1/02 1. INTRODUCTION iii)
Page 33 and 34: B-62564E-1/02 1. INTRODUCTION i) Of
Page 35 and 36: B-62564E-1/02 1. INTRODUCTION iv) D
Page 37 and 38: B-62564E-1/02 1. INTRODUCTION
Page 39 and 40: B-62564E-1/02 1. INTRODUCTION (vi)
Page 41 and 42: B-62564E-1/02 2. OPERATIONAL DEVICE
Page 55 and 56:
B-62564E-1/02 2. OPERATIONAL DEVICE
Page 57 and 58:
Page 59 and 60:
Page 61 and 62:
Page 63 and 64:
Page 65 and 66:
Page 67 and 68:
Page 69 and 70:
Page 71 and 72:
Page 73 and 74:
Page 75 and 76:
Page 77 and 78:
Page 79 and 80:
Page 81 and 82:
B-62564E-1/02 3. POWER ON/OFF 3. PO
Page 83 and 84:
B-62564E-1/02 4. MANUAL OPERATION 4
Page 85 and 86:
Page 87 and 88:
Page 89 and 90:
Page 91 and 92:
B-62564E-1/02 4. MANUAL OPERATION (
Page 93 and 94:
B-62564E-1/02 4. MANUAL OPERATION b
Page 95 and 96:
B-62564E-1/02 4. MANUAL OPERATION
Page 97 and 98:
Page 99 and 100:
Page 101 and 102:
Page 103 and 104:
Page 105 and 106:
Page 107 and 108:
Page 109 and 110:
Page 111 and 112:
B-62564E-1/02 4. MANUAL OPERATION B
Page 113 and 114:
Page 115 and 116:
B-62564E-1/02 5. AUTOMATIC OPERATIO
Page 117 and 118:
Page 119 and 120:
Page 121 and 122:
Page 123 and 124:
Page 125 and 126:
Page 127 and 128:
Page 129 and 130:
Page 131 and 132:
Page 133 and 134:
Page 135 and 136:
Page 137 and 138:
Page 139 and 140:
Page 141 and 142:
Page 143 and 144:
Page 145 and 146:
Page 147 and 148:
Page 149 and 150:
Page 151 and 152:
Page 153 and 154:
Page 155 and 156:
Page 157 and 158:
Page 159 and 160:
B-62564E-1/02 6. TEST OPERATION 6.4
Page 161 and 162:
B-62564E-1/02 6. TEST OPERATION 6.6
Page 163 and 164:
B-62564E-1/02 6. TEST OPERATION 5 S
Page 165 and 166:
B-62564E-1/02 6. TEST OPERATION (2)
Page 167 and 168:
B-62564E-1/02 6. TEST OPERATION (3)
Page 169 and 170:
B-62564E-1/02 6. TEST OPERATION ⋅
Page 171 and 172:
B-62564E-1/02 ÉÉÉÉÉÉÉÉÉÉ
Page 173 and 174:
B-62564E-1/02 7. SAFETY FUNCTIONS 7
Page 175 and 176:
B-62564E-1/02 9. STORING AND EDITIN
Page 177 and 178:
Page 179 and 180:
Page 181 and 182:
Page 183 and 184:
Page 185 and 186:
Page 187 and 188:
Page 189 and 190:
Page 191 and 192:
Page 193 and 194:
Page 195 and 196:
Page 197 and 198:
Page 199 and 200:
Page 201 and 202:
Page 203 and 204:
Page 205 and 206:
Page 207 and 208:
Page 209 and 210:
Page 211 and 212:
Page 213 and 214:
Page 215 and 216:
Page 217 and 218:
Page 219 and 220:
Page 221 and 222:
Page 223 and 224:
Page 225 and 226:
Page 227 and 228:
Page 229 and 230:
Page 231 and 232:
Page 233 and 234:
B-62564E-1/02 10. SETTING AND DISPL
Page 235 and 236:
Page 237 and 238:
Page 239 and 240:
Page 241 and 242:
Page 243 and 244:
Page 245 and 246:
Page 247 and 248:
Page 249 and 250:
Page 251 and 252:
Page 253 and 254:
Page 255 and 256:
Page 257 and 258:
Page 259 and 260:
Page 261 and 262:
Page 263 and 264:
Page 265 and 266:
Page 267 and 268:
Page 269 and 270:
Page 271 and 272:
Page 273 and 274:
Page 275 and 276:
Page 277 and 278:
Page 279 and 280:
Page 281 and 282:
Page 283 and 284:
Page 285 and 286:
Page 287 and 288:
Page 289 and 290:
Page 291 and 292:
Page 293 and 294:
Page 295 and 296:
Page 297 and 298:
Page 299 and 300:
Page 301 and 302:
Page 303 and 304:
Page 305 and 306:
Page 307 and 308:
Page 309 and 310:
Page 311 and 312:
Page 313 and 314:
Page 315 and 316:
Page 317 and 318:
Page 319 and 320:
Page 321 and 322:
Page 323 and 324:
Page 325 and 326:
Page 327 and 328:
Page 329 and 330:
Page 331 and 332:
Page 333 and 334:
Page 335 and 336:
Page 337 and 338:
B-62564E-1/02 11. DISPLAY At the bo
Page 339 and 340:
B-62564E-1/02 11. DISPLAY 11.1.3 Gr
Page 341 and 342:
B-62564E-1/02 11. DISPLAY (2) Group
Page 343 and 344:
B-62564E-1/02 11. DISPLAY (7) Curre
Page 345 and 346:
B-62564E-1/02 11. DISPLAY 11.3.2 Pr
Page 347 and 348:
B-62564E-1/02 11. DISPLAY 11.4 Oper
Page 349 and 350:
B-62564E-1/02 11. DISPLAY 11.6 Grap
Page 351 and 352:
B-62564E-1/02 11. DISPLAY (2) Graph
Page 353 and 354:
B-62564E-1/02 11. DISPLAY
Page 355 and 356:
B-62564E-1/02 11. DISPLAY In the ca
Page 357 and 358:
B-62564E-1/02 11. DISPLAY 11.6.3 Dr
Page 359 and 360:
B-62564E-1/02 11. DISPLAY (5) Enlar
Page 361 and 362:
B-62564E-1/02 11. DISPLAY (b) The D
Page 363 and 364:
B-62564E-1/02 11. DISPLAY NOTE 1 Se
Page 365 and 366:
B-62564E-1/02 11. DISPLAY 11.11 Clo
Page 367 and 368:
B-62564E-1/02 11. DISPLAY 11.12 Bac
Page 369 and 370:
B-62564E-1/02 11. DISPLAY (2) Rotat
Page 371 and 372:
B-62564E-1/02 11. DISPLAY (9) Graph
Page 373 and 374:
B-62564E-1/02 11. DISPLAY 11.12.4 D
Page 375 and 376:
B-62564E-1/02 11. DISPLAY (3) Custo
Page 377 and 378:
B-62564E-1/02 11. DISPLAY WAVE DIAG
Page 379 and 380:
B-62564E-1/02 11. DISPLAY NOTE The
Page 381 and 382:
B-62564E-1/02 11. DISPLAY 11.13.5 E
Page 383 and 384:
B-62564E-1/02 11. DISPLAY (5) Input
Page 385 and 386:
B-62564E-1/02 11. DISPLAY (3) Alarm
Page 387 and 388:
B-62564E-1/02 11. DISPLAY (7) Using
Page 389 and 390:
B-62564E-1/02 11. DISPLAY 11.15 Ope
Page 391 and 392:
B-62564E-1/02 11. DISPLAY When the
Page 393 and 394:
B-62564E-1/02 11. DISPLAY (c) Alarm
Page 395 and 396:
B-62564E-1/02 11. DISPLAY 1 Before
Page 397 and 398:
B-62564E-1/02 11. DISPLAY (iv) Oper
Page 399 and 400:
B-62564E-1/02 11. DISPLAY (3) Displ
Page 401 and 402:
B-62564E-1/02 11. DISPLAY [Cutter c
Page 403 and 404:
B-62564E-1/02 11. DISPLAY [Three-di
Page 405 and 406:
B-62564E-1/02 11. DISPLAY 11.17 Coo
Page 407 and 408:
B-62564E-1/02 11. DISPLAY (4) Offse
Page 409 and 410:
B-62564E-1/02 12. CRT SCREEN SAVING
Page 411 and 412:
B-62564E-1/02 13. DATA OUTPUT 13.2
Page 413 and 414:
B-62564E-1/02 13. DATA OUTPUT 13.4
Page 415 and 416:
B-62564E-1/02 14. DATA INPUT/OUTPUT
Page 417 and 418:
Page 419 and 420:
Page 421 and 422:
Page 423 and 424:
Page 425 and 426:
Page 427 and 428:
B-62564E-1/02 15. ABSOLUTE-POSITION
Page 429 and 430:
B-62564E-1/02 15. ABSOLUTE-POSITION
Page 431 and 432:
B-62564E-1/02 16. AXIS CONTROL 16.A
Page 433 and 434:
II. MAINTENANCE
Page 435 and 436:
1. ROUTINE MAINTENANCE B-62564E-1/0
Page 437 and 438:
Page 439 and 440:
Page 441 and 442:
Page 443 and 444:
2. REPLACING A FUSE B-62564E-1/02 2
Page 445 and 446:
3. REPLACING BATTERIES B-62564E-1/0
Page 447 and 448:
4. TROUBLESHOOTING B-62564E-1/02 4.
Page 449 and 450:
Page 451 and 452:
Page 453 and 454:
4. TROUBLESHOOTING B-62564E-1/02 Di
Page 455 and 456:
5. FAILURE DIAGNOSIS GUIDANCE B-625
Page 457 and 458:
APPENDIX
Page 459 and 460:
APPENDIX A . STATUS WHEN TURNING TH
Page 461 and 462:
APPENDIX B. RS-232-C AND RS-422 INT
Page 463 and 464:
Page 465 and 466:
Page 467 and 468:
Page 469 and 470:
Page 471 and 472:
Page 473 and 474:
Page 475 and 476:
Page 477 and 478:
APPENDIX C. WARNING MESSAGE LIST B-
Page 479 and 480:
APPENDIX D. LIST OF OPERATIONS B-62
Page 481 and 482:
APPENDIX E. CORRESPONDENCE BETWEEN
Page 483 and 484:
E Editing a displayed waveform, 359
Page 485 and 486:
Screen Saver Function, 386 Screen S
Page 487:
· No part of this manual may be re
show all

15-B Operation (Mach Ctr), GFZ-62564E-1/02

You also want an ePaper? Increase the reach of your titles

Delete template?

Save as template?